Regulations, Proposed Rules and Final rules determined by EPA
On this page:
- The difference between a 'Notice,' a 'Proposed Rule' (Proposal), and a 'Final Rule' (Rule)
- Final Rule by Publication Type
- Final Rule by Industrial Sector
The difference between a 'Notice,' a 'Proposed Rule' (Proposal), and a 'Final Rule' (Rule)
The SNAP program implements Section 612 of the amended Clean Air Act of 1990, which requires EPA to evaluate substitutes for the ozone-depleting substances to reduce overall risk to human health and the environment. Through these evaluations, SNAP generates lists of acceptable and unacceptable substitutes for each of the major industrial use sectors. The intended effect of the SNAP program is to promote a smooth transition to safer alternatives.
‘Notice’
Substitutes found acceptable without restriction will be published in a determination or notice of acceptability, or ‘Notice.’ This 'Notice' contains no regulatory controls and thus does not need to go through the notice-and-comment rulemaking process. It may contain technical corrections to earlier rules as well as listings of new agents that are acceptable without restrictions. It enters into force upon publication in the Federal Register.
‘Proposed Rule’ (Proposal)
Substitutes that are found unacceptable or acceptable subject to use restrictions will go through a comment period and then be published as a rule. A 'Proposed Rule' (Proposal) contains proposed lists of agents deemed acceptable (but subject to narrowed use limits or use conditions) or unacceptable. There is usually a 60-day public comment period beginning with the date of publication in the Federal Register.
‘Final Rule’ (Rule)
After the public has an opportunity to comment on EPA's proposed rules, EPA considers the comments and prepares and publishes a 'Final Rule' (Rule) that enacts the provisions into law. The SNAP rules and notices are available online on the Regulations page and can also be ordered for a nominal fee from the Government Publishing Office, (202) 512-1800, or fax (202) 512-2250.
Final Rule by Publication Type
Rules
The following rules list substitutes that have been determined unacceptableThis designation means that it is illegal to use a product as a substitute for an ODS in a specific end-use. For example, HCFC-141b is an unacceptable substitute for CFC-11 in building chillers. Note that all SNAP determinations apply to the use of a specific product as a substitute for a specific ODS in a specific end-use. , acceptable to use conditionsThis designation means that a substitute may be used, without restriction, to replace the relevant ODS within the end-use specified. For example, HCFC-22 is an acceptable substitute for R-502 in industrial process refrigeration. Note that all SNAP determinations apply to the use of a specific product as a substitute for a specific ODS in a specific end-use., and acceptable subject to narrowed use limitsThis designation indicates means that a substitute would be unacceptable unless its use was restricted to specific applications within an end-use. This designation is generally used when the specific characteristics of different applications within an end-use result in differences in risk. Use of the substitute in the end-use is legal only in those applications included within the narrowed use limit. Note that all SNAP determinations apply to the use of a specific product as a substitute for a specific ODS in a specific end-use.
Substitutes that are acceptableThis designation means that a substitute may be used, without restriction, to replace the relevant ODS within the end-use specified. For example, HCFC-22 is an acceptable substitute for R-502 in industrial process refrigeration. Note that all SNAP determinations apply to the use of a specific product as a substitute for a specific ODS in a specific end-use. without restriction are listed below in Notices of Acceptability
Final Rule 26 - Listing of Substitutes under the Significant New Alternatives Policy Program in Commercial and Industrial Refrigeration
This action lists substitutes for the refrigeration and air conditioning sector. The listings are as follows:
- List nine refrigerants as acceptable, subject to use conditions, for use in commercial ice machines;
- List nine refrigerants as acceptable, subject to use conditions, for use in industrial process refrigeration;
- List seven refrigerants as acceptable, subject to use conditions, for use in cold storage warehouses;
- List six refrigerants as acceptable, subject to use conditions, for use in ice skating rinks;
- List eight refrigerants as acceptable, subject to use conditions, for use in retail food refrigeration systems;
- Revise use conditions for one refrigerant, for use in self-contained commercial ice machines and stand-alone retail refrigeration equipment;
- Adopt the current versions of three industry standards by incorporating them by reference into the relevant use conditions; and
- Exempt R-290 from the Clean Air Act section 608 prohibition on releases of refrigerant during installing, maintaining, repairing, or disposing of refrigerated food processing and dispensing equipment on the basis of information that such releases are not expected to pose a threat to the environment.
- Final Rule 26 (June 13, 2024)
- Final Rule 26 Fact Sheet (PDF 3 pp, 322 KB)
- Proposed Rule 26 (May 24, 2023)
- Proposed Rule 26 Fact Sheet (PDF 3 pp, 375.17 KB)
Final Rule 25 - Listing of Substitutes under the Significant New Alternatives Policy Program in Refrigeration, Air Conditioning, and Fire Suppression
This action lists substitutes for the refrigeration and air conditioning and the fire suppression sectors. The listings are as follows:
- List six refrigerants as acceptable, subject to use conditions, for use in air conditioning in commercial and industrial buildings (“chillers”) and residential dehumidifiers;
- Revise use conditions for one refrigerant, for use in self-contained air conditioners and heat pumps for residential and light commercial use;
- List one refrigerant as acceptable, subject to use conditions and narrowed use limits, for use in very low temperature laboratory equipment;
- List three fire suppressants as acceptable, subject to use conditions; and
- Adopt the current versions of three industry standards by incorporating them by reference into the relevant use conditions.
- Final Rule (April 28, 2023) (PDF 49 pp, 584 KB)
- Final Rule Fact Sheet (PDF 3 pp, 312 KB)
- Proposed Rule (July 28, 2022) (PDF 55 pp, 918 KB)
- Proposed Rule Fact Sheet (PDF 3 pp, 295 K)
- Q&A About UL Standard 60335-2-40 Edition 4
Rule 24 - Listing of HFO-1234yf under the Significant New Alternatives Policy Program for Motor Vehicle Air Conditioning in Nonroad Vehicles and Servicing Fittings for Small Refrigerant Cans
This action expands the list of substitutes for motor vehicle air conditioning (MVAC). The changes are as follows:
-
Lists HFO-1234yf as acceptable, subject to use conditions, for MVAC systems in certain nonroad vehicles.
-
Adopts the current versions of the industry standards SAE J639, SAE J1739, and SAE J2844 in the use conditions for the proposed listings of HFO-1234yf in nonroad vehicles and previous listings for certain onroad vehicles.
-
Requires unique servicing fittings for small refrigerant cans (two pounds or less) of HFO-1234yf that are used to service MVAC systems in both onroad and nonroad vehicles.
- Adds a reference to EPA’s regulations under the Toxic Substances Control Act for HFO-1234yf for the proposed listings in nonroad vehicles and previous listings for certain onroad vehicles.
- Final Rule (May 4, 2022) (PDF 20 pp, 487 KB)
- Final Rule Fact Sheet (PDF 2 pp, 376 KB)
- Proposed Rule (December 6, 2021) (PDF 21 pp, 513 KB)
- Proposed Rule Fact Sheet (PDF 2 pp, 441 KB)
Rule 23 Supplemental proposal on foams and withdrawal notice
- Based on its consideration of comments and new information on alternatives, EPA is withdrawing the June 12, 2020, proposal and the October 6, 2021, supplemental proposal that proposed to list as acceptable the following three foam blowing agent blends containing HFCs:
- blends of 40 to 52 percent HFC-134a by weight and the remainder HFO-1234ze(E);
- blends of 40 to 52 percent HFC-134a with 40 to 60 percent HFO-1234ze(E) and 10 to 20 percent each water and CO2 by weight; and
- blends with maximum of 51 percent HFC-134a, 17 to 41 percent HFC-152a, up to 20 percent CO2 and one to 13 percent water.
To view the public docket, visit https://www.regulations.gov and search for Docket No. EPA-HQ-OAR-2019-0698. Information on how to provide comments is provided in the proposed rule.
- Withdrawal Notice (May 20, 2022) (PDF 4 pp, 244 KB)
- Supplemental Proposed Rule (October 6, 2021) (PDF 12 pp, 331 KB)
- Supplemental Proposed Rule Fact Sheet (PDF 2 pp, 243 KB)
Rule 23-New listings for refrigeration and air conditioning; revised listing for fire suppression
This action lists 9 substitutes for refrigeration and air conditioning. In addition, the action revises an existing listing for fire suppression. The listings are as follows:
-
List R-448A, R-449A and R-449B as acceptable, subject to narrowed use limits, for use in retail food refrigeration—medium-temperature stand-alone units for new equipment;
-
List R-452B, R-454A, R-454B, R-454C and R-457A as acceptable, subject to use conditions, for use in residential and light commercial air conditioning (AC) and heat pumps for new equipment; and R-32 as acceptable, subject to use conditions, for use in residential and light commercial AC and heat pumps—equipment other than self-contained room air conditioners, for new equipment (Note: R-32 was previously listed as acceptable, subject to use conditions, in self-contained room air conditioners [April 10, 2015; 80 FR 19454]);
-
Remove Powdered Aerosol E from the list of fire suppression substitutes acceptable subject to use conditions in total flooding applications.
EPA did not include foam blowing agents that were part of the June 2020 proposed rule in this final rule. EPA has withdrawn those proposed listings (see above Rule 23 supplemental proposal on foams).
To view the public docket, visit www.regulations.gov and search for Docket No. EPA-HQ-OAR-2019-0698.
- Final Rule (May 6, 2021)
- Final Rule Fact Sheet (PDF 2 pp, 258 KB)
- Proposed Rule (June 12, 2020) (PDF 22 pp, 482 KB)
- Proposed Rule Fact Sheet (PDF 2 pp, 239 KB)
- Q&A About UL Standard 60335-2-40 Edition 4
Rule 22- Revised use conditions for hydrocarbon refrigerants as substitutes for household refrigerators and freezers
- Final Rule
This final action modifies the use conditions required for use of three flammable refrigerants—isobutane (R-600a), propane (R-290), and R-441A—in new household refrigerators, freezers, and combination refrigerators and freezers under the Significant New Alternatives Policy (SNAP) program. The use conditions, which address safe use of flammable refrigerants, are being revised to reflect the updated UL Standard 60335-2-24 that is incorporated by reference.
To view the public docket, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2017-0472.
- Final Rule (August 8, 2018) (PDF 8 pp, 319 K)
- Final Rule Fact Sheet (PDF 1 p, 319 K)
Withdrawal of Direct Final Rule
- Withdrawal Notice for 12/11/2017 Direct Final Rule (March 7, 2018) (PDF 1 p, 338 K)
Direct Final Rule and Concurrent Notice of Proposed Rulemaking
- Direct Final Rule (December 11, 2017) (PDF 8 pp, 326 K)
- Concurrent Notice of Proposed Rulemaking (December 11, 2017) (PDF 3 pp, 218 K)
Rule 21- New listings of safer substitutes and prohibition on the use of certain high-GWP alternatives (December 1, 2016)
- EPA’s Significant New Alternatives Policy (SNAP) program expands the list of acceptable substitutes; lists unacceptable substitutes; and changes the status of a number of substitutes that were previously listed as acceptable, based on information showing that other substitutes are available for the same uses that pose lower risk overall to human health and/or the environment. Specifically, this rule lists as acceptable, subject to use conditions, a number of substances in the refrigeration and air conditioning, and fire suppression sectors; lists several substances as unacceptable in specific end-uses in the refrigeration and air conditioning sector; and changes the listing status for certain substances that were previously listed as acceptable in the refrigeration air conditioning and foam blowing sectors. EPA is also applying the existing listing decisions for foam blowing agents to closed cell foam products and products containing closed cell foam; and listing propane as acceptable, subject to use conditions, as a refrigerant in certain new equipment and exempting it in these end-uses from the venting prohibition under CAA section 608(c)(2). Finally, this rule clarifies the listing for Powdered Aerosol D, a fire suppression agent.
To view the public docket, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2015-0663.
- Final Rule (December 1, 2016) (PDF 118 pp, 969 KB)
- Final Rule Fact Sheet
- Proposed Rule - (April 18, 2016) (PDF 101 pp, 952 KB)
Rule 20- Prohibition on the use of certain high-GWP HFCs as alternatives
- Under this final rule, various hydrofluorocarbons (HFCs) and HFC-containing blends that were previously listed as acceptable alternatives under the SNAP program are now listed as unacceptable for specific uses. This rule is part of the SNAP program’s continuous review of alternatives to find those that pose less overall risk to human health and the environment. Specifically, this action changes the listing status for certain HFCs in various end-uses in the aerosols, refrigeration and air conditioning, and foam blowing sectors. This action also changes the status from acceptable to unacceptable for certain hydrochlorofluorocarbons (HCFCs) being phased out of production under the Montreal Protocol on Substances that Deplete the Ozone Layer and section 605(a) of the Clean Air Act, where substitutes are available that pose overall lower risk to human health and/or the environment.
To view the public docket, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2014-0198.
- Final Rule - (July 20, 2015) (PDF 91 pp, 807 KB)
- Final Rule Fact Sheet
- Proposed Rule
Rule 19- Refrigerant Alternatives
- Note: On August 8, 2018, EPA published a final rule to modify the use conditions required for use of the flammable refrigerant propane (R-290) in household refrigerators and freezers. See Rule 22 above.
This final action lists additional refrigerant substitutes as acceptable, subject to use conditions, in new equipment in six end-uses. The updates to the listings are as follows:
- Ethane in very low temperature refrigeration and in non-mechanical heat transfer
- Isobutane in retail food refrigeration (stand-alone commercial refrigerators and freezers) and in vending machines
- Propane in household refrigerators, freezers, or combination refrigerators and freezers, in vending machines, and in room air conditioning units
- The hydrocarbon blend R-441A in retail food refrigeration (stand-alone commercial refrigerators and freezers), in vending machines, and in room air conditioning units
- HFC-32 (difluoromethane) in room air conditioning units
This final action exempts from the §608 venting prohibition these hydrocarbon refrigerants for the specific applications listed above.
- Final Rule - (April 10, 2015) (PDF 49 pp, 890 KB)
- Final Rule Fact Sheet
- Proposed Rule (July 9, 2014) (PDF 30 pp, 418 KB)
- HTML Version (30pp, 248 KB)
- Print Version (PDF 30pp, 419 KB)
Rule 18- Fire Suppression Alternatives
- Final Rule for Fire Suppression Alternative
Effective Date: May 29, 2013
This rule lists C7 Fluoroketone as acceptable subject to narrowed use limits as a halon substitute for the streaming end-use. in the fire suppression and explosion protection sector. PDF Version (7 pp, 308 KB) HTML Version (7 p, 48 KB)
Withdrawal in Part of Direct Final Rule
Effective Date: December 14, 2012This notice withdraws C7 Fluoroketone from the direct final rule issued September 19, 2012. The listing of two other substitutes, Powdered Aerosols F (KSA) and Powdered Aerosol G (Dry Sprinkler Powdered Aerosol (DSPA) Fixed Generators), in that direct final rule remain in effect. PDF Version (1 p, 197 KB) HTML Version (1 p, 5 KB)
Direct Final Rule
Effective Date: December 18, 2012 for Powdered Aerosols F and GThis rule lists three halon substitutes in the fire suppression and explosion protection sector. Powdered Aerosol F and G are acceptable subject to use conditions in total flooding. C7 Fluoroketone is acceptable subject to narrowed use limits for the streaming end-use.
- Direct Final Rule: PDF Version (11 pp, 300 KB)
- Concurrent Proposal: PDF Version (4 pp, 204 KB)
Additional information: DSPA generators produce combustion byproducts (micron-sized dry particles and a gaseous mixture), that mix together into a uniform fire-extinguishing aerosol before being released into the protected area. The propellant components of the system generates inert gases, which function to physically extinguish the fire by the combined effects of straining the burning flame front and reducing the heat of the combustion sources. The small aerosol particles have a high surface area to-volume ratio, which increases their ability to rapidly distribute throughout enclosed areas and to act as heat sinks.
Rule 17- Listing of hydrocarbon refrigerants as substitutes for household refrigerators and freezers and retail food refrigeration
- Note: On August 8, 2018, EPA published a final rule to modify the use conditions required for use of the flammable refrigerants isobutane (R-600a) and R-441A in household refrigerators and freezers. See Rule 22 above.
Effective Date: February 21, 2012
- Final Rule: HTML Version and Print Version (27 pp, 298 KB) (December 20, 2011; 76 FR 78832)
- Proposed Rule: Print Version (17 pp, 248 KB) (May 10, 2010; 75 FR 25799)
Rule 16- HFO-1234yf as a new substitute for motor vehicle air conditioning
- Effective Date: May 21, 2012
Direct Final Amendment to Rule 16—Revised fitting for refrigerant containers of HFO-1234yf Effective Date: May 21, 2012
- Direct Final/Concurrent Proposal
- Direct Final Rule: HTML Version and PDF Version (8 pp, 261 KB) (March 26, 2012; 77 FR 17344)
- Concurrent Proposal: HTML Version and PDF Version (3 pp, 200 KB) (March 23; 77 FR 16988)
Effective Date: May 31, 2011
- Final Rule (March 29, 2011; 76 FR 17488)
- HTML Version and Print Version (34 pp, 366 KB)
- Fact Sheet
- Proposed Rule (October 19, 2009; 74 FR 53445)
- HTML Version and Print Version (10 pp, 86 KB)
Rule 15- Fire suppression and explosion protection listing under SNAP
- Effective Date: November 27, 2006
- Direct Final/Concurrent Proposal (September 21, 2006; 71 FR 56539 / 71 FR 56422)
- Direct Final Rule: HTML Version and Print Version (11 pp, 195 KB)
- Concurrent Proposal: HTML Version and Print Version (3 pp, 200 KB)
Rule 14- Alternatives for the motor vehicle air conditioning sector
- Effective Date: August 6, 2012
This rule lists R-744 (CO2) as an acceptable alternative with use conditions for motor vehicle air conditioning systems.
- Final Rule (June 6, 2012; 77 FR 33315
- HTML version and Print Version (16 pp, 345 KB)
This rule lists HFC-152a as an acceptable alternative with use conditions for motor vehicle air conditioning systems.
- Final Rule (June 12, 2008; 73 FR 33304)
- HTML Version and Print Version (8 pp, 137 KB)
- Proposed Rule (September 14, 2006; 71 FR 55140)
- HTML Version and Print Version (10 pp, 194 KB)
- Data Availability Notice (September 17, 2009; 74 FR 47774)
- HTML Version and Print Version (2 pp, 48 KB)
- This Data Availability Notice provides more information about, and seeks comment on, the short-term health effects of CO2 in confined spaces and potential use limitations as an automotive refrigerant.
Rule 13- The use of HCFC-22 and HCFC-142b in foams / listing of ozone depleting substitutes in foam blowing
- Effective Date: May 29, 2007
- Final Rule (March 28, 2007; 72 FR 14432)
- HTML Version and Print Version (12 pp, 198 KB)
- Proposed Rule (November 4, 2005; 70 FR 67120)
- HTML Version and Print Version
Rule 12- n-propyl bromide(nPB) in solvents cleaning, aerosols, and adhesives as a substitute for CFC-113, methyl chloroform, and HCFC-141b
-
- Proposed Rule for Adhesives, Coatings, and Aerosols (May 30, 2007; 72 FR 30168)
- Print Version (40 pp, 1.52 MB)
- Final Rule for Solvent Cleaning (May 30, 2007; 72 FR 30142)
- Print Version (27 pp, 451 kb)
The May 2007 final rule for nPB in solvent cleaning finds nPB an acceptable substitute for ozone depleting substances in metals, electronics, and precision cleaning.
- Corrections to Proposed Rule (October 2, 2003; 68 FR 56809)
- Proposed Rule (June 3, 2003; 68 FR 33284)
- Corrections to the Advance Notice of Proposed Rulemaking (March 25, 1999; 64 FR 14417)
- Advance Notice of Proposed Rulemaking (February 18, 1999; 64 FR 8043)
The June 3, 2003 rule proposed to list n-propyl bromide (nPB) as an acceptable substitute for ozone depleting substances (ODSs), subject to use conditions, in the solvent cleaning sector as well as aerosol solvents and adhesive uses. EPA initially proposed that the use of nPB is acceptable subject to a use condition, limiting contaminants of nPB formulations from isopropyl bromide.
Rule 11- Fire suppression substitutes
- Effective Date: March 28, 2003
- Correction to Final Rule, Typographical Errors (April 7, 2003; 68 FR 16749)
- Correction to Final Rule, Additional Information (April 7, 2003; 68 FR 16729)
- Final Rule (January 27, 2003; 68 FR 4004)
EPA is issuing its decision on the acceptability of three halon substitutes in the fire suppression and explosion protection sector. HFC227BC found acceptable subject to use conditions in total flooding. C6-perfluoroketone and H Golden HFPEs found acceptable subject to narrowed use limits for the streaming end-use.
Rule 10- Acceptable and unacceptable substitutes for ozone-depleting substances (ODSs) in foams blowing
- Effective Date: September 30, 2004
- Final Rule (September 30, 2004; 69 FR 58269)
- Notice of Data Availability (March 10, 2004; 69 FR 11358)
This action finds HCFC-141b unacceptable for use as a substitute for ODSs in all end uses in the foam blowing sector, except for specified exemptions, including use in space vehicles, nuclear energy, defense, and research and development for foreign customers.
Effective Date: August 21, 2002- Final Rule (July 22, 2002; 67 FR 47703)
- Notice of Data Availability (May 23, 2001; 66 FR 28408)
- Proposed Rule (July 11, 2000; 65 FR 42653)
This action lists acceptable and unacceptable substitutes for ozone-depleting substances (ODSs) in the foam-blowing sector. The final rule withdraws the proposed decision to list HCFC-22 and HCFC-142b as unacceptable substitutes for existing users; lists HCFC-22 and HCFC-142b as unacceptable substitutes for HCFC-141b in rigid polyurethane/ polyisocyanurate laminated boardstock, rigid polyurethane appliance foam, and rigid polyurethane spray foam applications; lists HCFC-22 and HCFC-142b as acceptable substitutes for HCFC-141b, with narrowed use limits (users must ascertain and document that other acceptable alternatives are not technically feasible) in commercial refrigeration and sandwich panel applications and in the rigid polyurethane slabstock and other foams end-use; and lists HCFC-124 as an unacceptable substitute in all foam end-uses. At this time, EPA is deferring final action on its proposed decision to list HCFC-141b as an unacceptable foam-blowing agent.
Rule 9- Removal of restrictions on certain fire suppression substitutes for ozone-depleting substances (ODSs), and a list of substitutes
- Effective Date: April 1, 2002
- Final Rule: Print Version (19 pp, 237 KB) (January 29, 2002; 67 FR 4185)
-
Concurrent Proposed Rule: Print Version (4 pp, 170 KB) (January 29, 2002; 67 FR 4222)
EPA is rescinding use conditions that limit human exposure to halocarbon and inert gas agents used in the fire suppression and explosion protection industry. These use conditions are redundant with safety standards established by the National Fire Protection Association (NFPA). In addition, EPA is taking direct final action to change the listing for HBFC-22B1 from acceptable subject to use conditions to unacceptable.
Rule 8- Prohibition for the use of refrigerant blends containing hexafluoropropylene
- Effective Date: January 26, 1999
- Interim Final Rule Prohibiting the Use of Refrigerant Blends Containing Hexafluoropropylene (January 26, 1999; 64 FR 3865)
Hexafluoropropylene (HFP) and any blend containing HFP are listed as unacceptable for substitutes for CFC-12 and HCFC-22.
Rule 7- MT-31 as an unacceptable refrigerant under EPA's Significant New Alternatives Policy (SNAP) Program
- Effective Date: January 26, 1999
- Interim Final Rule Prohibiting the use of MT-31 (January 26, 1999; 64 FR 3861)
The refrigerant blend MT-31 is listed as unacceptable for all refrigeration and air-conditioning end-uses.
Rule 6- Listing of two substitutes for ozone-depleting substances (ODSs) in the fire suppression and explosion protection sector
- Effective Date: May 26, 2000
- Final Rule (April 26, 2000; 65 FR 24387)
- Corrections to Proposed Rule (March 25, 1999; 64 FR 14417)
- Proposed Rule (February 18, 1999; 64 FR 8038)
This action lists two substitutes for halon B1301 and halon 1211, IG-100,and HCFC Blend E in the fire suppression and explosion protection sector as acceptable, subject to use restrictions. Substitute IG-100 is for the end-use of total flooding systems and HCFC Blend E is for the end-use of streaming agents.
Rule 5- Two gases found unacceptable as substitutes for refrigerants in "self-chilling cans"
- Effective Date: April 2, 1999
- Final Rule (March 3, 1999; 64 FR 10373)
- Proposed Rule (February 3, 1998; 63 FR 5491)
The action of this rule, lists unacceptable the use of HFC-134a and HFC-152a as refrigerants in "self-chilling cans."
Rule 4- Listing of motor vehicle air-conditioning systems substitutes and a range of certain other substitutes
- Effective Date: May 28, 1999
- Final Rule (April 28, 1999; 64 FR 22981)
- Proposed Rule (May 21, 1997; 62 FR 27873)
This action clarifies the criteria for unique fittings used in motor vehicle air-conditioning systems, and addresses the acceptability of HFC-4310mee and HCFC-225ca/cb. The end-uses for these substitutes are in metal cleaning and solvent in aerosols. C3F8, HFC-236fa, and C4F10 are found acceptable with use conditions for halon 1301 in-fire suppression and explosion prevention. The unacceptability of substitutes in the refrigeration and air conditioning, solvents, aerosols, fire suppression, and adhesives, coatings, & inks sectors are also listed.
Rule 3- Cross-media evaluation of risks to human health and environment by sector end-use
- Effective Date: November 15, 1996
- Final Rule (October 16, 1996; 61 FR 54029)
- Proposed Rule (May 22, 1996; 61 FR 25604)
EPA issued its decisions on the acceptability HFC-4310mee, HCFC-141b, perfluoropolyethers, and perfluorocarbons. The end-uses of these substitutes are electronic and precision cleaning as well as aerosol solvents.
Rule 2- Cross-media evaluation of risks to human health and environment by sector
- Effective Date: June 21, 1996
- Final Rule (May 22, 1996; 61 FR 25585)
- Proposed Rule (October 2, 1995; 60 FR 51383)
EPA is issuing its preliminary decisions on the acceptability of substitutes not previously reviewed by the Agency. Monochlorotoluenes/benzotrifluorides are acceptable subject to use conditions as substitutes for CFC-113 and MCF in electronics, precision, and metals cleaning. Blend Zeta and HCFC Blend Delta are acceptable as substitutes for CFC-12 in retrofitted and new motor vehicle air conditioners, subject to the use conditions applicable to motor vehicle air conditioning.
Rule 1- Comment response document of public options concerning EPA rulemaking
- Effective Date: July 13, 1995
- Final Rule (June 13, 1995; 60 FR 31092)
- Proposed Rule (September 26, 1994; 59 FR 49108)
EPA issued decisions on refrigerants and solvent cleaning sectors found acceptable subject to use conditions. The refrigeration sector deals with end-uses both retrofit and new equipment. HCFC Blend Beta was found as acceptable subject to use conditions for motor vehicle air conditioning. Blend B was found acceptable subject to use conditions for; centrifugal chillers, chillers, industrial process refrigeration, skating rinks, storage warehouses, refrigerated transport, food refrigeration, ice machines, freezers, dehumidifiers, and air conditioners. HCFC-225 ca/cb is decided as a substitute for CFC-113 and MCF acceptable to use conditions in precision and metals cleaning. Various other substitutes were found unacceptable for refrigerants and air conditioning as well as in the solvents cleaning sector.
SNAP Final Rule - Process for administering the SNAP program and EPA's first acceptability lists
- Effective Date: April 18, 1994
- SNAP Final Rule (March 18, 1994; 59 FR 13044)
- SNAP Proposal (May 12, 1993; 58 FR 28094)
- SNAP ANPRM (Jan. 16, 1992; 57 FR 1984)
EPA published the SNAP Final Rule, which described the process for administering the SNAP program and issued EPA's first acceptability lists for substitutes in the major industrial use sectors. These sectors include:
- Adhesives, Coatings, and Inks
- Aerosols
- Cleaning Solvents
- Fire Suppression and Explosion Protection
- Foam Blowing Agents
- Refrigeration and Air Conditioning
- Sterilants
- Tobacco Expansion
To assess the acceptability of a substitute, the Agency completes a screening analysis in which overall risks to human health and the environment in use-specific applications are examined. EPA continues to publish updates to the SNAP Final Rule in the form of a “Notice of Acceptability” or a “Rule.”
SNAP Notices of Acceptability
These notices expand the list of acceptableThis designation means that a substitute may be used, without restriction, to replace the relevant ODS within the end-use specified. For example, HCFC-22 is an acceptable substitute for R-502 in industrial process refrigeration. Note that all SNAP determinations apply to the use of a specific product as a substitute for a specific ODS in a specific end-use. or pending substitutes for ozone depleting substances (ODSs) under the U.S. Environmental Protection Agency's (EPA) Significant New Alternatives Policy (SNAP) program. The substitutes listed below are acceptable without restriction in the specific end-uses unless designated as pending. A pending substitute can be sold after the 90 day review period has expired, but its acceptability may be affected by a subsequent rulemaking. To see substitutes that are restricted or prohibited, see the list of rules above.
Notice 38
-
Effective Date: September 8, 2023Acceptability Determination 38 (September 8, 2023; 88 FR 61977)
This action presents EPA’s most recent decision to list as acceptable several substitutes in the refrigeration and air conditioning and fire suppression sectors. New substitutes are:
- R-471A in industrial process refrigeration (new equipment only), cold storage warehouses (new equipment only), retail food refrigeration – stand-alone equipment (new equipment only), retail food refrigeration – refrigerated food processing and dispensing equipment (new equipment only), retail food refrigeration – remote condensing units (new equipment only), and retail food refrigeration – supermarket systems (new equipment only);
- R-515B in cold storage warehouses (new equipment only), commercial ice machines (new equipment only), retail food refrigeration – refrigerated food processing and dispensing equipment (new equipment only), retail food refrigeration – remote condensing units (new equipment only), and retail food refrigeration – supermarket systems (new equipment only); and
- Powdered Aerosol I as a total flooding agent for use in occupied and normally unoccupied spaces.
To review the public docket for this notice, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2003-0118.
Notice 37
-
Effective Date: January 20, 2022Acceptability Determination 37 (January 20, 2022; 87 FR 3037)
- HTML Format
- PDF (Adobe Acrobat) File (pdf)
- Fact Sheet (PDF 2 pp, 234 KB)
This action presents EPA’s most recent decision to list as acceptable several substitutes in the refrigeration and air conditioning, foam blowing, aerosols, cleaning solvents, and coatings sectors. New substitutes are:
- Hydrochlorofluoroolefin (HCFO)-1233zd(E) in cold storage warehouses, ice rinks, and industrial process air conditioning (new equipment only);
- Blends of 10 to 90 percent hydrofluoroolefin (HFO)-1234ze(E) by weight and the remainder hydrochlorofluoroolefin (HCFO)-1233zd(E) in polystyrene: extruded boardstock and billet (XPS);
- Blends of 10 to 90 percent HFO-1234ze(E) by weight and the remainder hydrofluorocarbon (HFC)-152a in XPS;
- Blends of zero to 100 percent HFO-1234ze(E), zero to 70 percent methyl formate, zero to 60 percent HFC-152a, zero to 60 percent CO2, and zero to 60 percent water in XPS; and
- HCFO-1233yd(Z) in electronics cleaning, metals cleaning, and precision cleaning, aerosol solvents, and coatings.
To review the public docket for this notice, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2003-0118.
Notice 36
-
Effective Date: December 11, 2020Acceptability Determination 36 (December 11, 2020; FR2020-23861)
This action presents EPA’s most recent decision to list as acceptable several substitutes in the refrigeration and air conditioning, foam blowing, and fire suppression sectors. New substitutes are:
- Hydrochlorofluoroolefin (HCFO)-1233zd(E) in industrial process refrigeration (new and retrofit equipment);
- R-515B in centrifugal and positive displacement chillers and industrial process air conditioning (new equipment);
- Blends of 10 to 99 percent by weight hydrofluoroolefin (HFO)-1336mzz(Z) and the remainder hydrofluorocarbon (HFC)-152a in polystyrene: extruded boardstock and billet;
- HFO-1336mzz(E) in a number of foam blowing end-uses;
- Methylal in rigid polyurethane (PU) spray foam (high-pressure two-component, low-pressure two-component, and one-component foam sealants); and
- HCFO-1233zd(E)/C6-perfluoroketone blend in total flooding fire suppression (normally occupied and unoccupied spaces).
Notice 35
-
Effective Date: November 25, 2019
Acceptability Determination 35 (November 25, 2019; 84 FR 64765)
- HTML Format
- PDF (Adobe Acrobat) File (8pp., 348 K)
- Fact Sheet
This action presents EPA’s most recent decision to list as acceptable several substitutes in the refrigeration and air conditioning sector. New substitutes are:
- R-1224yd(Z) in centrifugal chillers (new and retrofit equipment), industrial process refrigeration (new and retrofit equipment), and positive displacement chillers (new and retrofit equipment);
- R-407H in refrigerated transport--refrigerated trucks and trailers (new and retrofit equipment), retail food refrigeration--refrigerated food processing and dispensing equipment (new and retrofit equipment), and retail food refrigeration--supermarket systems (new and retrofit equipment);
- R-448A, R-449A, and R-449B in ice skating rinks (new equipment); and
- R-453A in refrigerated transport--refrigerated trucks and trailers (new and retrofit equipment).
This action also clarifies the types of equipment included in the refrigerated transport—refrigerated trucks and trailers end-use category.
To review the public docket for this notice, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2003-0118.
Notice 34
-
Effective Date: October 4, 2018
Acceptability Determination 34 (October 4, 2018; 83 FR 50026)
- PDF (Adobe Acrobat) File (10pp., 306 K)
- Fact Sheet
This action presents EPA’s most recent decision to list as acceptable several substitutes in the refrigeration and air conditioning, foam blowing, fire suppression, cleaning solvents, and aerosols sectors. New substitutes are:
- R-448A, R-449A, and R-449B in ice skating rinks (retrofit equipment only);
- R-450A and R-513A in ice skating rinks (new and retrofit equipment):
- Acetone/isopentane blend in rigid polyurethane and polyisocyanurate laminated boardstock;
- Powdered Aerosol E in total flooding fire suppression (normally occupied areas); and
- HFO-1336mzz(Z) in electronics cleaning, metals cleaning, and precision cleaning and aerosol solvents.
To review the public docket for this notice, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2003-0118.
Notice 33
-
Effective Date: July 21, 2017
Acceptability Determination 33 (July 21, 2017; 82 FR 33809)
- HTML Format
- PDF (Adobe Acrobat) File (17pp., 331 K)
- Fact Sheet
This action presents EPA’s most recent decision to list as acceptable several substitutes in the refrigeration and air conditioning and cleaning solvent sectors. New substitutes are:
- HFC-134a in residential and light commercial air conditioning and heat pumps (retrofit equipment);
- HFE-7300 in non-mechanical heat transfer systems (new and retrofit equipment), electronics cleaning, metals cleaning, and precision cleaning end-uses;
- R-407H and R-442A in retail food refrigeration—remote condensing units (new and retrofit equipment);
- R-448A, R-449A, R-449B, R-452A, R-452C, R-453A, and R-458A in multiple refrigeration and air conditioning end-uses (new and retrofit equipment); and
- R-513A in residential dehumidifiers (new and retrofit equipment).
To review the public docket for this notice, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2003-0118.
Notice 32
-
Effective Date: October 11, 2016
Acceptability Determination 32 (October 11, 2016; 81 FR 70029)
- HTML Format
- PDF (Adobe Acrobat) File (10 pp., 283 K)
- Fact Sheet
This action presents EPA's most recent decision to list as acceptable several substitutes in the refrigeration and air conditioning and fire suppression sectors. New substitutes are:
- R-448A in retail food refrigeration—food processing and dispensing equipment;
- R-449A in retail food refrigeration—food processing and dispensing equipment;
- R-449B in several refrigeration end-uses; and
- trans-1-chloro-3,3,3,-trifluoroprop-1-ene in total flooding fire suppression uses.
To review publicly available docket materials electronically, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2003-0118. Supporting materials are also available in the Air and Radiation docket in hard copy.
Notice 31
-
Effective Date: May 23, 2016
Acceptability Determination 31 (May 23, 2016; 81 FR 32241)
- HTML Format
- PDF (Adobe Acrobat) File (9 pp., 313 K)
- Fact Sheet (Adobe Acrobat) File (1 p, 136 K)
EPA is adding options for refrigeration and air conditioning that offer better climate protection without harming the ozone layer. The Determination of Acceptability expands the SNAP program’s list of acceptable substitutes by adding a number of substitutes with lower GWPs compared to what are predominately used today for the same uses. New substitutes are:
- CO2 in several refrigeration and air conditioning end-uses;
- HFO-1336mzz(Z) in several refrigeration and air conditioning end-uses;
- HFO-1336mzz(Z)/trans-1,2-dichloroethylene blend in centrifugal and positive-displacement chillers; and
- R-513A in retail food refrigeration—food processing and dispensing equipment.
To review the public docket for this notice, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2003-0118.
Notice 30
-
Effective Date: July 16, 2015
Acceptability Determination 30 (July 16, 2015; 80 FR 42053)
- HTML Format
- PDF (Adobe Acrobat) File (14 pp., 354 K)
EPA is adding options for refrigeration and air conditioning; foam blowing; solvent cleaning; aerosols; and adhesives, coatings, and inks that offer better climate protection without harming the ozone layer. The Determination of Acceptability expands the SNAP program’s list of acceptable substitutes by adding a number of substitutes with lower GWPs compared to what are predominately used today for the same uses. New substitutes are:
- R-450A in new vending machines;
- R-448A, R-513A, and R-449A in several refrigeration and air conditioning end-uses;
- Methoxytridecafluoroheptene isomers in non-mechanical heat transfer, three solvent cleaning end-uses, aerosol solvents; and adhesives and coatings; and
- Hydrofluoroolefin (HFO)-1336mzz(Z) for high-pressure two-part spray foam.
To review the public docket for this notice, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2003-0118.
Notice 29
-
Effective Date: October 21, 2014
Acceptability Determination 29 (October 21, 2014; 79 FR 62863)
- HTML Format
- PDF (Adobe Acrobat) File (8 pp., 283 K)
EPA is increasing the options for refrigerants, foam blowing agents, and fire suppressants that offer better climate protection without harming the ozone layer. On October 15, 2014, a Notice of Acceptability was signed expanding the Significant New Alternatives Policy (SNAP) program’s list of acceptable substitutes by adding a number of substitutes with lower global warming potentials (GWPs) compared to what are predominately used today for the same uses. This action also builds on the announcements made on September 16th concerning new private sector commitments to reduce emissions of hydrofluorocarbons (HFCs).
The notice lists the following as acceptable:
- trans-1-chloro-3,3,3-trifluoroprop-1-ene in non-mechanical heat transfer, and in flexible polyurethane foams
- CO2 in refrigerated transport
- R-450A in a variety of refrigeration and air conditioning end-uses
- Methylal in a variety of foam blowing end-uses
- Hydrofluoroolefin (HFO)-1336mzz(Z) in a variety of foam blowing end-uses
- Powdered Aerosol D in the total flooding end-use
To review the public docket for this notice, visit www.regulations.gov and search for docket number EPA-HQ-OAR-2003-0118.
Notice 28
-
Effective Date: May 17, 2013
Acceptability Determination 28 (May 17, 2013; 78 FR 29034)
- HTML Format
- PDF (Adobe Acrobat) File (8 pp., 283 K)
This notice expands the list of acceptable substitutes for end uses in the refrigeration and air conditioning, foam blowing, solvent cleaning, aerosol and fire suppression sectors. The determinations concern new substitutes.
- Erratum: In section I.B.1, the text incorrectly identifies HFC-365mfc as 1,1,1,3,3-pentafluoropropane with Chemical Abstracts Service Registry Number (CASRN) 138495-42-8. The correct name is 1,1,1,3,3-pentafluorobutane and the correct CASRN is 406-58-6.
- Erratum: In section I.A.1, the text incorrectly indicates that R-442A contains 31.1 percent by weight HFC-32 and 31.1 percent by weight HFC-125. The correct amount for each constituent is 31.0 percent.
Notice 27
-
Effective Date: August 10, 2012
Acceptability Determination 27 (August 10, 2012; 77 FR 47768)
PDF (Adobe Acrobat) File (12 pp., 320 K)
This notice expands the list of acceptable substitutes for end uses in the refrigeration and air conditioning; foam blowing; solvent cleaning; adhesives, coatings and inks; and fire suppression sectors. The determinations concern new substitutes.
Notice 26
-
Effective Date: October 4, 2011
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, solvent cleaning and fire suppression. The determinations concern new substitutes.
Acceptability Determination 26 (Oct. 4, 2011; 76 FR 61269)
- Erratum: In section B.1, the text incorrectly says that HCFC-225ca has a GWP of 1,220. This should instead read “122.”. Source: IPCC, 2007: Climate Change 2007: The Physical Science Basis. Contribution of Working Group I to the Fourth Assessment Report of the Intergovernmental Panel on Climate Change (Solomon, S., D. Qin, M. Manning, Z. Chen, M. Marquis, K.B. Averyt, M. Tignor and H.L. Miller (eds.)). Cambridge University Press, Cambridge, United Kingdom and New York, NY, USA.
Notice 25
-
Effective Date: June 16, 2010
- Notice 25 (June 16, 2010; 75 FR 34017)
This notice lists acceptable substitutes for HCFC-22, HCFC-142b, and blends thereof for end uses in refrigeration and air conditioning, foam blowing, aerosols, and sterilants. The determinations all include substitutes previously listed as substitutes for other ODS or as substitutes for HCFC-22 alone.
- Environmental, Health, and Flammability Information on Substitutes for HCFC-22 and HCFC 142b in the Refrigeration and Air Conditioning Sector
- Environmental, Health, and Flammability Information on Substitutes for HCFC-22 and HCFC 142b in the Foam Blowing Agents Sector
- Environmental, Health, and Flammability Information on Substitutes for HCFC-22 and HCFC 142b in the Aerosols Sector
- Environmental, Health, and Flammability Information on Substitutes for HCFC-22 and HCFC 142b in the Sterilants Sector
Notice 24
-
Effective Date: September 30, 2009
- Notice 24 (September 30, 2009; 74 FR 50129)
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning and foam blowing. The determinations concern new substitutes. In addition, this document informs the public that the refrigerant blend previously found acceptable under the name KDD5 has received the ASHRAE designation R-438A and has the trade name ISCEON® MO99.
Notice 23
-
Effective Date: January 2, 2009
- Notice 23 (January 2, 2009; 74 FR 21)
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, fire suppression, and foam blowing. The determinations concern new substitutes.
Notice 22
-
Effective Date: October 4, 2007
- Notice 22 (October 4, 2007; 72 FR 56628)
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning. The determinations concern new substitutes.
Notice 21
-
Effective Date: September 28, 2006
- Notice 21 (September 28, 2006; 71 FR 56884)
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, foam blowing, cleaning solvents, aerosols, and sterilants. The determinations concern new substitutes.
Notice 20
-
Effective Date: March 29, 2006
- Notice 20 (March 29, 2006; 71 FR 15589)
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, foam blowing, and fire suppression and explosion protection. The determinations concern new substitutes.
Notice 19
-
Effective Date: October 1, 2004
- Notice 19 (October 1, 2004; 69 FR 58903)
EPA has found acceptable additional substitutes for use in the following sectors: refrigeration and air conditioning, foam blowing, fire suppression and explosion protection, and sterilants. This document also clarifies the status of the use of a hydrochlorofluorocarbon as an aerosol solvent, revises the global warming potential for a substitute previously listed as acceptable for use in fire suppression and explosion protection based on new information, and clarifies a statement from the previous SNAP notice of acceptability of August 21, 2003, regarding a refrigerant.
Notice 18
-
Effective Date: August 21, 2003
- Notice 18 (August 21, 2003; 68 FR 50533)
The EPA has approved acceptable substitutes for use in the following sectors: refrigeration and air conditioning, solvents cleaning, foam blowing, fire suppression and explosion protection, and aerosols.
- Refrigeration and air-conditioning sector EPA has found acceptable RS-44 as a substitute for HCFC-22 and R-407C as a substitute for R-502 in the following end-uses (new and retro-fit); industrial process refrigeration, industrial process air conditioning, ice skating rinks, cold storage warehouses, refrigerated transport, retail food refrigeration, vending machines, water coolers, commercial ice machines, household refrigerators and freezers, centrifugal chillers, reciprocating chillers, screw chillers, non-mechanical heat transfer systems, household and light commercial air conditioning, as well as residential dehumidifiers. Also, EPA decided ISCEON 89 as an acceptable substitute for R-13B1 in very low temperature refrigeration.
- EPA has decided acceptable for the solvent cleaning sector HFE-7000 as a substitute for CFC-113, methyl chloroform, and HCFC-141b in the end-uses of precision cleaning and electronics cleaning.
- The foam blowing sector EPA decided acceptable Ecomate as a substitute for CFC and HCFCs, HCF-245fa as a substitute for HCFCs and blends of HFC-245fa and HCFC-22 as a substitute for blends of HCFC-141b and HCFC-22 in the following end-uses; rigid polyurethane and polyisocyanurate laminated boardstock, rigid polyurethane appliance foam, rigid polyurethane slabstock and other foams, rigid polyurethane commercial refrigeration and sandwich panels, polyurethane integral skin foam, phenolic insulation board and bunstock, and polyolefin.
- EPA has decided for the fire suppression and explosion protection sectors NAF S-125 as an acceptable substitute for halon 1301 in the end-use of total flooding.
- In the aerosol sector, HFE-7000 is an acceptable substitute for CFC-113, methyl chloroform, HCFC-141b in the end-use of aerosol solvents.
Notice 17
-
Effective Date: December 20, 2002
- Correction to Notice 17 (April 7, 2003; 68 FR 16728)
- Notice 17 (December 20, 2002; 67 FR 77927)
The EPA has approved acceptable substitutes for use in the following sectors: refrigeration and air conditioning, solvents cleaning, fire suppression and explosion protection, and aerosols.
- EPA's decision for acceptable substitutes in refrigeration and air conditioning are RS-24 as a substitute for CFC-12, NU-22 as a substitute for R-502, and R-404A, R-507A, R-407C as substitutes for HCFC-22 and HCFC blends. The end-uses for these substitutes are; industrial process refrigeration, industrial process air conditioning (only new), ice skating rinks, cold storage warehouses, refrigerated transport, retail food refrigeration, vending machines, water coolers, commercial ice machines, household refrigerators and freezers, reciprocating chillers, centrifugal chillers, screw chillers, very low temperature refrigeration, non-mechanical heat transfer systems, household and light commercial air conditioning, residential dehumidifiers.
- EPA's decision for the solvent cleaning sector of HCFC-225ca and HCFC-225cb as acceptable substitutes for CFC-113 and methyl chloroform for metal cleaning.
- EPA's decision for the fire suppression and explosion protection sector of C6-perfluoroketone as an acceptable substitute for halon 1301.
- EPA's decision for the aerosol sector of HCFC-225ca and HCFC-225cb as acceptable substitutes for HCFC-141b in the end-use of aerosol solvents.
Notice 16
-
Effective Date: March 22, 2002
- Notice 16 (March 22, 2002; 76 FR 13272)
The ozone depleting substitutes are for use in the following sectors: refrigeration and air conditioning; aerosols; and adhesives, coatings, and inks. In addition, we are notifying the public of new information available on the toxicity of HCFC-225ca and HCFC-225cb, acceptable substitutes used in solvents cleaning.
Notice 15
-
Effective Date: May 23, 2001
- Notice 15 (May 23, 2001; 66 FR 28179)
EPA's decision for acceptable substitute uses in the refrigeration and air conditioning sector.
- HFC-134a/HBr (98/8) as a substitute for CFC-12 and R-502, with the end uses of retail food refrigeration and cold storage warehouses for primary heat transfer fluid in new secondary-loop equipment for not-in-kind replacements of systems and the end-use of refrigerated transport.
- HFC-134a/HBr (92/8) as an acceptable substitutes for CFC-11, CFC-12, CFC-114, CFC-115, and R-507 in the end-use of industrial process refrigeration.
- PFC-330ST, PFC-550HC, PFC-660HC, PFC-1100HC, PFC-1100LT, PGC-100, PGC-150, PFC-331ST, PFC-551HC, PFC-661HC, PFC-1101HC, and PGC-151 as acceptable substitutes for CFC- 13, CFC-113, CFC-114, and blends thereof for the end-use of very low temperature refrigeration (new and retrofit).
Notice 14
-
Effective Date: December 18, 2000
- Correction to Notice 14 (March 7, 2001; 66 FR 13655)
- Notice 14 (December 18, 2000; 65 FR 78977)
This notice identifies EPA's decisions of acceptable substitutes for refrigeration, air conditioning, foams, non-aerosol solvent cleaning, and aerosol solvents. This action also requests information on the composition and safety of certain refrigerants for motor vehicle air conditioners. This notice also requests information on whether the SNAP program should include review of and establishment of use conditions for operations that involve manual cleaning with solvents or restriction of non-aerosol solvent substitutes to equipment that meets the cleaning equipment standards in the National Emission Standards for Halogenated Solvent Cleaning. Finally, this action updates readers on the SNAP program's review of n-propyl bromide for use as a substitute for ozone-depleting solvents used in the non-aerosol solvents cleaning, aerosol solvents and propellants, and adhesives, coatings and inks sectors.
- Hydrofluoroether 7100 and Hydrofluoroether 7200 for CFC-11, CFC-12, CFC-114, CFC-115, HCFC-22, R-502, R-503, and R-13B1 in the refrigeration and air-conditioning end-uses of industrial process refrigeration, retail food refrigeration, and very low temperature refrigeration, as a secondary heat transfer fluid in new equipment for not-in-kind replacements of systems. Also, non-mechanical heat transfer for use in retrofit and new equipment.
- FOR12A and FOR12B for an acceptable substitute of HCFC-22 and CFC-12, NU-22 for an acceptable substitute of HCFC-22, and SP34E for an acceptable substitute of CFC-12 for the refrigeration and air-conditioning end-uses; industrial process refrigeration and air-conditioning, industrial process refrigeration, cold storage warehouses, refrigerated transport, retail food refrigeration, ice machines, vending machines, water coolers, centrifugal chillers, reciprocating chillers, household refrigerators and freezers, residential air conditioning and heat pumps, residential dehumidifiers, motor vehicle air conditioning and buses only.
- Methyl formate as an acceptable substitute for CFCs and HCFCs in the following foam sector end-uses; rigid polyurethane and polyisocyanurate laminated boardstock, rigid polyurethane appliances, rigid polyurethane slabstock and other foams, rigid polyurethane commercial refrigeration and sandwich panels, and polyurethane integral skin foam.
- Hydrofluoroether 7100 as an acceptable substitute for HCFC-141b and HCFC-22; Heptafluorocyclopentane as acceptable substitutes for CFC-113, methyl chloroform, and HCFC-141b; and HFC-365mfc as an acceptable substitute for CFC-113, methyl chloroform, and HCFC-141b in the non-aerosol solvent cleaning end-uses of all metals cleaning, precision cleaning, and electronics cleaning applications.
Notice 13
-
Effective Date: June 19, 2000
- Notice 13 (June 19, 2000; 65 FR 37900)
There are listing of substitutes for refrigeration and air conditioning as well as foam blowing.
- The refrigeration and air conditioning acceptable substitutes are HFC-4310mee for CFCs and HCFCs, Ikon A and Ikon B for CFC-12, and HFC-245fa for CFC-11 (new only). These substitutes are for the following end uses: non-mechanical heat transfer, household refrigeration and freezers, commercial comfort air conditioning, cold storage warehouses, industrial process refrigerators and air conditioners, refrigerated transport, retail food refrigeration, vending machines, water coolers, commercial ice machines, and small auxiliary power units.
- Vacuum panels are acceptable as substitutes for HCFC blown rigid polyurethane appliance foam, and 2-chloropropane is acceptable for HCFCs in rigid polyurethane and polyisocyanurate laminated boardstock foam.
Notice 12
-
Effective Date: April 11, 2000
- Notice 12 (April 11, 2000; 65 FR 19327)
This notice deals with acceptable substitutes for refrigeration, air conditioning, and foam blowing. The end uses for refrigeration and air-conditioning are uranium isotope separation processing (retrofit), using furan as an acceptable substitute for CFC-114. All foam-blowing end uses are included, for saturated light hydrocarbons C3-C6 for HCFC-141b, except HCFC-141b replacement in spray foam applications.
Notice 11
-
Effective Date: December 6, 1999
- Notice 11 (December 6, 1999; 64 FR 68039)
This notice applies to substitutes for refrigeration, air conditioning, foam blowing, solvents cleaning sector, and aerosols.
- HFC-245fa is acceptable as a substitute for CFC-11 and HCFC-141b in all foam end-uses.
- Exxsol Blowing Agents are acceptable substitutes for HCFC-141b in all foam end-uses.
- Hydrofluoroether (HFE-7200) is an acceptable substitute for CFC-113 and methyl chloroform (MCF) in all solvents cleaning end-uses and solvents in aerosol products.
- THR-02 is acceptable as a substitute for CFC-12 in the following end-uses: Industrial process refrigeration and air-conditioning, cold storage warehouses, refrigerated transport, retail food refrigeration, ice machines, vending machines, water coolers, centrifugal chillers, reciprocating chillers, household refrigerators and freezers.
- THR-03 is acceptable as a substitute for HCFC- 22 in the following end-uses: Industrial process refrigeration and air-conditioning, cold storage warehouses, refrigerated transport, retail food refrigeration, ice machines, centrifugal chillers, reciprocating chillers, ice skating rinks, household refrigerators and freezers, and residential window unit air-conditioning.
- ISCEON 59 is acceptable as a substitute for R- 22 in the following end-uses: Household and light commercial air-conditioning, commercial comfort air-conditioning, industrial process refrigeration and air-conditioning, cold storage warehouses, refrigerated transport, retail food refrigeration, ice machines, vending machines, water coolers, centrifugal chillers, reciprocating chillers, household and other refrigerated appliances, ice skating rinks, and non-mechanical heat transfer.
- HFC-152a is acceptable as a substitute for CFC-12 in the following end-uses: Industrial process refrigeration and air-conditioning, cold storage warehouses, refrigerated transport, retail food refrigeration, ice machines, vending machines, water coolers, centrifugal chillers, reciprocating chillers, and residential dehumidifiers.
- The cryo-mechanical cryogenic transport system that uses recaptured and recycled liquid carbon dioxide or liquid nitrogen is acceptable as a substitute for R-502 or CFC-12 in the transport refrigeration end-use.
- Hydrofluroether (HFE-7200) is an acceptable substitute for CFC-113 in non-mechanical heat transfer.
Notice 10
-
Effective Date: June 8, 1999
- Notice 10 (June 8, 1999; 64 FR 30410)
This notice includes substitutes for; adhesives, coatings, and ink sector, aerosols sector, solvents sector, foams sector, and refrigeration and air conditioning sector. Refrigeration and air conditioning end uses include all R-502 end uses in addition to non-mechanical heat transfer, very low temperature refrigeration, and motor vehicle air conditioners. All end uses are applicable for solvent cleaning, aerosol solvents, adhesives, coatings, and ink sector.
- THR-04 is acceptable as a substitute for R-502 in all refrigeration and air conditioning end-uses.
- HFC-236fa, when manufactured using any process that does not convert perfluoroisobutylene (PFIB) directly to HFC-236fa in a single step, is acceptable as a substitute for CFC-114 in non-mechanical heat transfer.
- HFE-7100, Hydrofluoroether, is an acceptable substitute for CFC-113 in non-mechanical heat transfer.
- HFC-23 is acceptable as a substitute for CFC-12 in very low-temperature refrigeration.
- HFC-134a and HFC-152a are acceptable substitutes for HCFCs in all foam blowing end-uses.
- Carbon dioxide and water are acceptable substitute for HCFCs in all foam blowing end-uses.
- HFC-4310mee is acceptable as a substitute for HCFC-141b in all solvents cleaning and aerosol solvent end-uses.
- Benzotrifluoride is an acceptable substitute with an exposure limit (AEL) of 100 ppm for all solvent cleaning, aerosols solvents, adhesives, coatings, and inks end-uses.
Notice 9
-
Effective Date: May 22, 1998
- Notice 9 (May 22, 1998; 63 FR 28251)
This is a summary of acceptable decisions of substitutes for aerosol propellants. CFC-11, CFC-12, CFC-114, HCFC-22, and HCFC-142b are being replaced by HFC-227ea.
Notice 8
-
- Notice 8 (February 24, 1998; 63 FR 9151)
This notice contains substitutes for end uses in solvent cleaning, aerosols, foam blowing, and refrigeration and air conditioning. The end uses for foam blowing are CFCs, HCFCs, and polyurethane integral skin, with acceptable substitutions of formic acid and acetone. The end uses for aerosol solvents are CFC-11, CFC-113, MCF, and HCFC-141b, with an acceptable substitution of C5-C20 petroleum hydrocarbons. The solvent end uses include metal cleaning, electronic cleaning and precision cleaning with CFC-113. There are many refrigeration and air conditioning end-uses.
Notice 7
-
Effective Date: June 3, 1997
- Notice 7 (June 3, 1997; 62 FR 30275)
This notice lists GHG-X5, MT-31, HCFC-22, HCFC-142b, and GHG-X5 as substitutes for foam blowing, refrigeration, and air conditioning. The foam blowing end uses are HCFCs, polyurethane integral skin with an acceptable substitute of sub-saturated light hydrocarbons C3-C6. CFC-12 centrifugal and reciprocating chillers, industrial process refrigeration, cold storage warehouses, refrigerated transport, retail food refrigeration, vending machines, water coolers, commercial ice machines, household refrigerators, household freezers, and residential dehumidifiers (retrofitted and new). Also, CFC-12 motor vehicle air conditioning, automotive and non-automotive (retrofitted and new).
Notice 6
-
Effective Date: March 10, 1997
- Notice 6 (March 10, 1997; 62 FR 10700)
This notice contains substitutes for refrigeration and the foam sector. Substitutes include HFC-236fa and saturated light hydrocarbons C3-C6. The refrigeration sector end-use is CFC-114 industrial process refrigeration, with an acceptable substitute of HFC-236fa. The foam sector acceptable decisions are for the end-uses of HCFCs rigid polyurethane and polyisocyanurate laminated boardstock, HCFCs rigid polyurethane appliance, and saturated light hydrocarbons C3-C6. There are various acceptable substitutes for these end uses in the foam sector.
Notice 5
-
Effective Date: September 5, 1996
- Notice 5 (September 5, 1996; 61 FR 47012)
This notice expands the list of acceptable and pending substitutes and clarifies information on refrigerant blends R-410A, R-410B, and R-407C that EPA previously added to the acceptable substitute list. This notice lists acceptable substitutes in various and uses in refrigeration and air conditioning, foam blowing, fire suppression, explosion protection, solvent cleaning, aerosols, adhesives, coatings, and inks. There are also pending substitutes, n-propyl bromide and HFC-4310, listed in aerosols and solvent cleaning.
- Hot Shot, GHG-X4, Freezone, Freeze 12, G2018C, NARM-502, and R-401C are acceptable substitutes for the refrigeration and air conditioning sectors.
- R-507, ammonia, evaporative and desiccant cooling, and water/lithium bromide are acceptable substitutes for HCFC-22 in refrigeration and air conditioning end-uses.
- Proprietary Blowing Agent 1 (PBA 1) is an acceptable substitute for CFCs in HCFCs for rigid polyurethane and polyisocyanurate laminated boardstock foam; rigid polyurethane appliance; rigid polyurethane slabstock and other; and rigid polyurethane spray and commercial refrigeration, and sandwich panels.
- Foam A is acceptable as a Halon 1301 substitute for fire suppression and explosion protection.
- Hydrofluoroether (HFE-7100) is an acceptable substitute for CFC-113 and methyl chloroform (MCF) in solvents cleaning, and aerosol solvents.
- Trans-1, 2-dichloroethylene is acceptable as an alternative to MCF and CFC-113 in adhesives.
Notice 4
-
Effective Date: February 8, 1996
- Notice 4 (February 8, 1996; 61 FR 4736)
This notice lists acceptable substitutes for the end-uses of refrigerants, fire suppression and explosion protection, foam blowing, and solvent cleaning.
- HCFC Blend Beta was listed as containing HFC-134a, HCFC-124, and isobutane. In fact, according to the submission on file with EPA, this blend contains butane. The determination that this blend is acceptable subject to certain use conditions applied to the actual blend, not to the incorrectly listed one.
- R-508, which contains HFC-23 and R-116, is acceptable as a substitute for CFC-13, R-13B1, and R-503 in retrofitted and new very low temperature refrigeration.
- HCFC Blend Delta is acceptable as a substitute for CFC-12 in retrofitted household refrigerators and freezers.
- HCFC Blend Lambda is acceptable as a substitute for R-500 in retrofitted centrifugal chillers and as a substitute for CFC-12 in the following new and retrofitted end-uses.
- R-410A, R-410B, and R-407C are acceptable substitutes for HCFC-22. The following are the new end-uses for the substitutes: centrifugal, reciprocating, and screw chillers, industrial process refrigeration systems, very-low-temperature industrial process refrigeration, industrial process air conditioning, ice skating rinks, refrigerated transport, retail food refrigeration, cold storage warehouses, vending machines, water coolers, commercial ice machines, household refrigerators and freezers, residential dehumidifiers, household and light commercial air conditioning.
- HFC-134a is acceptable as a substitute for HCFC-22 in new Household and Light Commercial Air Conditioning.
Notice 3
-
Effective Date: July 28, 1995
- Notice 3 (July 28, 1995; 60 FR 38729)
This notice lists acceptable substitutes for end-uses in refrigeration and air conditioning sector, as well as fire suppression and explosion protection sector.
- Octamethylcyclotetrasiloxanes and decamethylcyclopentasiloxanes are acceptable as substitutes for CFC-11, CFC-12, CFC-113, CFC-114, and CFC-115 in new and retrofitted heat transfer systems in the refrigeration and air conditioning sector.
- Water is acceptable as a substitute for CFC-11, CFC-12, CFC-113, CFC-114, and CFC-115 in new and retrofitted heat transfer systems.
- Mineral oil is acceptable as a substitute for CFC- 11, CFC-12, CFC-113, CFC-114, and CFC-115 in new and retrofitted heat transfer systems.
- R-508, which contains HFC-23 and R-116, is acceptable as a substitute for CFC-13, R-13B1, and R-503 in retrofitted and new industrial process refrigeration.
- Ammonia absorption is acceptable as an alternative technology to household refrigerators and freezers using CFC-12 as a refrigerant.
- Water Mist systems using potable water or natural seawater are acceptable as Halon 1301 and Halon 1211 substitutes.
Notice 2
-
Effective Date: January 13, 1995
- Notice 2 (January 13, 1995; 60 FR 3318)
This notice states acceptable substitutes for the refrigeration and air conditioning sector, as well as the foam blowing sector.
- R-401A and R-401B, which consist of HCFC-22, HFC-152a, and HCFC- 124, are acceptable as substitutes for CFC-11, CFC-12, R-500, and R-502 in various refrigeration and air conditioning end-uses.
- CO2 is acceptable as a substitute for CFC-13, R-13B1, and R-503 in various refrigeration and air conditioning end-uses.
- HCFC-22 and HFC-134a are acceptable as substitutes for R-400 (60/40) and CFC-114 in New Industrial Process Air Conditioning.
- R-401A and R-401B are acceptable as a substitutes for R-400(60/40) and CFC-114 in Retrofitted Industrial Process Air Conditioning.
- R-404A, which consists of HFC-125, HFC-143a, and HFC-134a, is acceptable as a substitute for CFC-12 in new household refrigerators.
- R-507, which consists of HFC-125 and HFC-143a, is acceptable as a substitute for CFC-12 in new household refrigerators.
- Hydrocarbon Blend B is acceptable as a substitute for CFC-12 in retrofitted and new industrial process refrigeration systems.
Notice 1
-
Effective Date: August 26, 1994
- Notice 1 (August 26, 1994; 59 FR 44240)
This notice lists acceptable substitutes for the refrigeration and air conditioning sector, foam blowing sector, solvent cleaning sector, fire suppression and explosion protection sector, and the aerosol sector.
- R-406A is acceptable as a substitute for R-500 in retrofitted centrifugal chillers.
- HCFC-123, R-406, R-407A, R-407B, and HCFC Blend Epsilon are acceptable substitutes for CFC-11, CFC-12, and R-502 for end-uses in the refrigeration and air conditioning sectors.
- HFC-23, R-403, and PFC Blend Alpha are acceptable substitute for CFC-13, R-13B1, and R-503 in the refrigeration and air conditioning sectors.
- HCFC Blend Gamma is acceptable as a substitute for CFC-12 and R-502 in various end-uses in refrigeration and air conditioning.
- R-402A and R-402B are acceptable as substitutes for CFC-11, CFC-12, and R-502 in retrofitted household freezers.
- R-507 is acceptable as a substitute for CFC-12 and R-502 in various end-uses in refrigeration and air conditioning.
- The Electroset Manufacturing Technology is an acceptable substitute for CFC-11 blown rigid polyurethane and polyisocyanurate laminated boardstock foams.
- HFC-143a is acceptable as an alternative to CFC-12 in polystyrene boardstock and billet foams.
- Saturated Light Hydrocarbons C3-C6 Saturated light hydrocarbons C3-C6 (and blends thereof) are acceptable as substitutes for CFC-11 and methyl chloroform in polyurethane flexible foam.
- Methylene chloride is acceptable as a substitute for CFC-11, CFC-12, and CFC-114 in polyolefin foams.
- Polyolefin Chemical Blend A is an acceptable substitute for CFC-11, CFC-12, and CFC-114 in polyolefin foams.
- HFC-152a/Saturated Light Hydrocarbons C3-C6 blends are acceptable substitutes for CFC-11, CFC-12, and CFC-114 in polyolefin foams.
- Trans-1, 2-dichloroethylene is acceptable as an alternative to MCF and CFC-113 in electronic, precision, and metals cleaning.
- Octamethylcyclotetrasiloxanes and decamethylcyclopentasiloxanes are acceptable alternatives to MCF and CFC-113 in electronic, precision, and metals cleaning.
- HCFC-123 is an acceptable substitute for CFC-113 and MCF in precision cleaning.
- HCFC-124, HCFC Blend C, HCFC Blend D, and Gelled Halocarbon/Dry Chemical Suspension are acceptable as Halon 1211 substitutes.
- HCFC Blend A is acceptable as a medical sterilant substitute for 12/88 CFC-12/EtO.
Other SNAP Federal Register Publications
- Notification of Guidance and a Stakeholder Meeting Concerning the Significant New Alternatives Policy Program
This document provides information related to EPA’s Significant New Alternatives Policy (SNAP) program final rule issued on July 20, 2015, and the decision of the Court of Appeals for the District of Columbia Circuit in the case of Mexichem Fluor, Inc. v. EPA vacating the rule in part and remanding to the Agency. This document provides guidance on how EPA plans to implement the court’s partial vacatur in the near term, pending a rulemaking, and information on the Agency’s plan to address the remand of the 2015 Rule through rulemaking. The Agency is also providing notice of a stakeholder meeting in advance of that rulemaking to be held on May 4, 2018 at EPA HQ.
EPA has not established a new docket for this document. Publicly available information on the related SNAP 2015 Rule can be found at www.regulations.gov and search for docket number EPA-HQ-OAR-2014-0198
- Notice of Data Availability; Reports on CO2 Total Flooding Fire Extinguishing Systems (May 11, 2004; 69 FR 26059)
- Notice of Data Availability; New Information Concerning SNAP Program Proposal on HCFC Use in Foams (May 23, 2001; 66 FR 28408)
Final Rule by Industrial Sector
Rules
The following rules list substitutes that have been determined unacceptableThis designation means that it is illegal to use a product as a substitute for an ODS in a specific end-use. For example, HCFC-141b is an unacceptable substitute for CFC-11 in building chillers. Note that all SNAP determinations apply to the use of a specific product as a substitute for a specific ODS in a specific end-use. , acceptable to use conditions, and acceptable subject to narrowed use limits.
Substitutes that are acceptableThis designation means that a substitute may be used, without restriction, to replace the relevant ODS within the end-use specified. For example, HCFC-22 is an acceptable substitute for R-502 in industrial process refrigeration. Note that all SNAP determinations apply to the use of a specific product as a substitute for a specific ODS in a specific end-use. without restriction are listed below in Notices of Acceptability
-
Refrigeration & Air Conditioning
Rule 20 (PDF 91 pp, 807 KB) - Prohibition on the use of certain high-GWP HFCs as alternatives
Publication Date: July 20, 2015
Effective Date: August 19, 2015
Federal Register Citation: 80 FR 42870Rule 17 (27 pp, 298 KB) - Listing of hydrocarbon refrigerants as substitutes for household of refrigerators and freezers and retail food refrigeration
Publication Date: December 20, 2011
Effective Date: February 21, 2012
Federal Register Citation: 76 FR 78832Rule 16 (8 pp, 261 KB) - HFO-1234yf as a new substitute for motor vehicle air conditioning
Publication Date: March 26, 2012
Effective Date: May 21, 2012
Federal Register Citation: 77 FR 17344Rule 14 (16 pp, 345 KB) - Alternatives for the motor vehicle air conditioning sector
Publication Date: June 6, 2012
Effective Date: August 6, 2012
Federal Register Citation: 77 FR 33315Description
This rule lists HFC-152a as an acceptable alternative with use conditions for motor vehicle air conditioning systems.Rule 3 (9 pp, 159 KB) - Cross-media evaluation of risks to human health and environment by sector end-use
Publication Date: October 16, 1996
Effective Date: November 15, 1996
Federal Register Citation: 61 FR 54029Description
EPA issued its decisions on the acceptability HFC-4310mee, HCFC-141b, perfluoropolyethers, and perfluorocarbons. The end-uses of these substitutes are electronic and precision cleaning as well as aerosol solvents.Rule 2 - Cross-media evaluation of risks to human health and environment by sector
Publication Date: May 22, 1996
Effective Date: June 21, 1996
Federal Register Citation: 61 FR 25585Description
EPA is issuing its preliminary decisions on the acceptability of substitutes not previously reviewed by the Agency. Monochlorotoluenes/benzotrifluorides are acceptable subject to use conditions as substitutes for CFC-113 and MCF in electronics, precision, and metals cleaning. Blend Zeta and HCFC Blend Delta are acceptable as substitutes for CFC-12 in retrofitted and new motor vehicle air conditioners, subject to the use conditions applicable to motor vehicle air conditioning.Publication Date: July 13, 1995
Effective Date: July 13, 1995
Federal Register Citation: 60 FR 31092Description
EPA issued decisions on refrigerants and solvent cleaning sectors found acceptable subject to use conditions. The refrigeration sector deals with end-uses both retrofit and new equipment. HCFC Blend Beta was found as acceptable subject to use conditions for motor vehicle air conditioning. Blend B was found acceptable subject to use conditions for; centrifugal chillers, chillers, industrial process refrigeration, skating rinks, storage warehouses, refrigerated transport, food refrigeration, ice machines, freezers, dehumidifiers, and air conditioners. HCFC-225 ca/cb is decided as a substitute for CFC-113 and MCF acceptable to use conditions in precision and metals cleaning. Various other substitutes were found unacceptable for refrigerants and air conditioning as well as in the solvents cleaning sector.Publication Date: March 18, 1994
Effective Date: April 18, 1994
Federal Register Citation: 59 FR 13044Description
This final rule promulgates the U.S. Environmental Protection Agency's (EPA) program for evaluating and regulating substitutes for ozone-depleting chemicals being phased out under the stratospheric ozone protection provisions of the Clean Air Act (CAA). In section 612 of the CAA, the Agency is authorized to identify and restrict the use of substitutes for class I and II ozone-depleting substances where the Administrator has determined that other alternatives exist that reduce overall risk to human health and the environment. EPA is referring to the program that provides these determinations as the Significant New Alternatives Policy (SNAP) program. The intended effect of this final rule is to expedite movement away fromozone-depleting compounds by identifying substitutes that offer lower overall risks to human health and the environment. -
Foam Blowing Agents
Rule 20 (PDF 91 pp, 807 KB) - Prohibition on the use of certain high-GWP HFCs as alternatives
Publication Date: July 20, 2015
Effective Date: August 19, 2015
Federal Register Citation: 80 FR 42870Rule 10 (27 pp, 298 KB) - Acceptable and unacceptable substitutes for ozone-depleting substances (ODSs) in foams blowing
Publication Date: September 30, 2004
Effective Date: September 30, 2004
Federal Register Citation: 69 FR 58269Description
This action lists acceptable and unacceptable substitutes for ozone-depleting substances (ODSs) in the foam-blowing sector. The final rule withdraws the proposed decision to list HCFC-22 and HCFC-142b as unacceptable substitutes for existing users; lists HCFC-22 and HCFC-142b as unacceptable substitutes for HCFC-141b in rigid polyurethane/ polyisocyanurate laminated boardstock, rigid polyurethane appliance foam, and rigid polyurethane spray foam applications; lists HCFC-22 and HCFC-142b as acceptable substitutes for HCFC-141b, with narrowed use limits (users must ascertain and document that other acceptable alternatives are not technically feasible) in commercial refrigeration and sandwich panel applications and in the rigid polyurethane slabstock and other foams end-use; and lists HCFC-124 as an unacceptable substitute in all foam end-uses. At this time, EPA is deferring final action on its proposed decision to list HCFC-141b as an unacceptable foam-blowing agent. -
Cleaning Solvents
Rule 12 (40 pp, 1.52 MB) - n-propyl bromide(nPB) in solvents cleaning, aerosols, and adhesives as a substitute for CFC-113, methyl chloroform, and HCFC-141b
Publication Date: May 30, 2007
Federal Register Citation: 72 FR 30142Rule 4 (6 pp, 264 KB) - Listing of motor vehicle air-conditioning systems substitutes and a range of certain other substitutes
Publication Date: April 28, 1999
Effective Date: May 28, 1999
Federal Register Citation: 64 FR 22981Description
This action clarifies the criteria for unique fittings used in motor vehicle air-conditioning systems, and addresses the acceptability of HFC-4310mee and HCFC-225ca/cb. The end-uses for these substitutes are in metal cleaning and solvent in aerosols. C3F8, HFC-236fa, and C4F10 are found acceptable with use conditions for halon 1301 in-fire suppression and explosion prevention. The unacceptability of substitutes in the refrigeration and air conditioning, solvents, aerosols, fire suppression, and adhesives, coatings, & inks sectors are also listed.Rule 3 (9 pp, 159 KB) - Cross-media evaluation of risks to human health and environment by sector end-use
Publication Date: October 16, 1996
Effective Date: November 15, 1996
Federal Register Citation: 61 FR 54029Description
EPA issued its decisions on the acceptability HFC-4310mee, HCFC-141b, perfluoropolyethers, and perfluorocarbons. The end-uses of these substitutes are electronic and precision cleaning as well as aerosol solvents.Rule 2 - Cross-media evaluation of risks to human health and environment by sector
Publication Date: May 22, 1996
Effective Date: June 21, 1996
Federal Register Citation: 61 FR 25585Description
EPA is issuing its preliminary decisions on the acceptability of substitutes not previously reviewed by the Agency. Monochlorotoluenes/benzotrifluorides are acceptable subject to use conditions as substitutes for CFC-113 and MCF in electronics, precision, and metals cleaning. Blend Zeta and HCFC Blend Delta are acceptable as substitutes for CFC-12 in retrofitted and new motor vehicle air conditioners, subject to the use conditions applicable to motor vehicle air conditioning.Publication Date: July 13, 1995
Effective Date: July 13, 1995
Federal Register Citation: 60 FR 31092Description
EPA issued decisions on refrigerants and solvent cleaning sectors found acceptable subject to use conditions. The refrigeration sector deals with end-uses both retrofit and new equipment. HCFC Blend Beta was found as acceptable subject to use conditions for motor vehicle air conditioning. Blend B was found acceptable subject to use conditions for; centrifugal chillers, chillers, industrial process refrigeration, skating rinks, storage warehouses, refrigerated transport, food refrigeration, ice machines, freezers, dehumidifiers, and air conditioners. HCFC-225 ca/cb is decided as a substitute for CFC-113 and MCF acceptable to use conditions in precision and metals cleaning. Various other substitutes were found unacceptable for refrigerants and air conditioning as well as in the solvents cleaning sector.Publication Date: March 18, 1994
Effective Date: April 18, 1994
Federal Register Citation: 59 FR 13044Description
This final rule promulgates the U.S. Environmental Protection Agency's (EPA) program for evaluating and regulating substitutes for ozone-depleting chemicals being phased out under the stratospheric ozone protection provisions of the Clean Air Act (CAA). In section 612 of the CAA, the Agency is authorized to identify and restrict the use of substitutes for class I and II ozone-depleting substances where the Administrator has determined that other alternatives exist that reduce overall risk to human health and the environment. EPA is referring to the program that provides these determinations as the Significant New Alternatives Policy (SNAP) program. The intended effect of this final rule is to expedite movement away fromozone-depleting compounds by identifying substitutes that offer lower overall risks to human health and the environment. -
Aerosols
Rule 20 (PDF 91 pp, 807 KB) - Prohibition on the use of certain high-GWP HFCs as alternatives
Publication Date: July 20, 2015
Effective Date: August 19, 2015
Federal Register Citation: 80 FR 42870Rule 4 (6 pp, 264 KB) - Listing of motor vehicle air-conditioning systems substitutes and a range of certain other substitutes
Publication Date: April 28, 1999
Effective Date: May 28, 1999
Federal Register Citation: 64 FR 22981Description
This action clarifies the criteria for unique fittings used in motor vehicle air-conditioning systems, and addresses the acceptability of HFC-4310mee and HCFC-225ca/cb. The end-uses for these substitutes are in metal cleaning and solvent in aerosols. C3F8, HFC-236fa, and C4F10 are found acceptable with use conditions for halon 1301 in-fire suppression and explosion prevention. The unacceptability of substitutes in the refrigeration and air conditioning, solvents, aerosols, fire suppression, and adhesives, coatings, & inks sectors are also listed.Rule 3 (9 pp, 159 KB) - Cross-media evaluation of risks to human health and environment by sector end-use
Publication Date: October 16, 1996
Effective Date: November 15, 1996
Federal Register Citation: 61 FR 54029Description
EPA issued its decisions on the acceptability HFC-4310mee, HCFC-141b, perfluoropolyethers, and perfluorocarbons. The end-uses of these substitutes are electronic and precision cleaning as well as aerosol solvents.Rule 2 - Cross-media evaluation of risks to human health and environment by sector
Publication Date: May 22, 1996
Effective Date: June 21, 1996
Federal Register Citation: 61 FR 25585Description
EPA is issuing its preliminary decisions on the acceptability of substitutes not previously reviewed by the Agency. Monochlorotoluenes/benzotrifluorides are acceptable subject to use conditions as substitutes for CFC-113 and MCF in electronics, precision, and metals cleaning. Blend Zeta and HCFC Blend Delta are acceptable as substitutes for CFC-12 in retrofitted and new motor vehicle air conditioners, subject to the use conditions applicable to motor vehicle air conditioning.Publication Date: March 18, 1994
Effective Date: April 18, 1994
Federal Register Citation: 59 FR 13044Description
This final rule promulgates the U.S. Environmental Protection Agency's (EPA) program for evaluating and regulating substitutes for ozone-depleting chemicals being phased out under the stratospheric ozone protection provisions of the Clean Air Act (CAA). In section 612 of the CAA, the Agency is authorized to identify and restrict the use of substitutes for class I and II ozone-depleting substances where the Administrator has determined that other alternatives exist that reduce overall risk to human health and the environment. EPA is referring to the program that provides these determinations as the Significant New Alternatives Policy (SNAP) program. The intended effect of this final rule is to expedite movement away fromozone-depleting compounds by identifying substitutes that offer lower overall risks to human health and the environment. -
Fire Suppression and Explosion Protection
Rule 20 (PDF 91 pp, 807 KB) - Prohibition on the use of certain high-GWP HFCs as alternatives
Publication Date: July 20, 2015
Effective Date: August 19, 2015
Federal Register Citation: 80 FR 42870Rule 18 (7 pp, 308 KB) - Fire Suppression Alternatives
Publication Date: April 29, 2013
Effective Date: May 29, 2013Description
This notice withdraws C7 Fluoroketone from the direct final rule issued September 19, 2012. The listing of two other substitutes, Powdered Aerosols F (KSA) and Powdered Aerosol G (Dry Sprinkler Powdered Aerosol (DSPA) Fixed Generators), in that direct final rule remain in effect.Additional Information
DSPA generators produce combustion byproducts (micron-sized dry particles and a gaseous mixture), that mix together into a uniform fire-extinguishing aerosol before being released into the protected area. The propellant components of the system generates inert gases, which function to physically extinguish the fire by the combined effects of straining the burning flame front and reducing the heat of the combustion sources. The small aerosol particles have a high surface areato-volume ratio, which increases their ability to rapidly distribute throughout enclosed areas and to act as heat sinks.Rule 15 (11 pp, 195 KB) - Fire suppression and explosion protection listing under SNAP
Publication Date: September 21, 2006
Effective Date: November 27, 2006
Federal Register Citation: 71 FR 56539 / 71 FR 56422Description
This notice withdraws C7 Fluoroketone from the direct final rule issued September 19, 2012. The listing of two other substitutes, Powdered Aerosols F (KSA) and Powdered Aerosol G (Dry Sprinkler Powdered Aerosol (DSPA) Fixed Generators), in that direct final rule remain in effect.Rule 11 (8 pp, 186 KB) - Fire suppression substitutes
Publication Date: January 27, 2003
Effective Date: March 28, 2003
Federal Register Citation: 68 FR 4004Description
EPA is issuing its decision on the acceptability of three halon substitutes in the fire suppression and explosion protection sector. HFC227BC found acceptable subject to use conditions in total flooding. C6-perfluoroketone and H Golden HFPEs found acceptable subject to narrowed use limits for the streaming end-use.Rule 9 (11 pp, 195 KB) - Removal of restrictions on certain fire suppression substitutes for ozone-depleting substances (ODSs), and a list of substitutes
Publication Date: January 29, 2002
Effective Date: April 1, 2002
Federal Register Citation: 67 FR 4185Description
EPA is rescinding use conditions that limit human exposure to halocarbon and inert gas agents used in the fire suppression and explosion protection industry. These use conditions are redundant with safety standards established by the National Fire Protection Association (NFPA). In addition, EPA is taking direct final action to change the listing for HBFC-22B1 from acceptable subject to use conditions to unacceptable.Rule 6 (6 pp, 264 KB) - Listing of two substitutes for ozone-depleting substances (ODSs) in the fire suppression and explosion protection sector
Publication Date: April 26, 2000
Effective Date: May 26, 2000
Federal Register Citation: 65 FR 24387Description
This action lists two substitutes for halon B1301 and halon 1211, IG-100,and HCFC Blend E in the fire suppression and explosion protection sector as acceptable, subject to use restrictions. Substitute IG-100 is for the end-use of total flooding systems and HCFC Blend E is for the end-use of streaming agents.Rule 4 (6 pp, 264 KB) - Listing of motor vehicle air-conditioning systems substitutes and a range of certain other substitutes
Publication Date: April 28, 1999
Effective Date: May 28, 1999
Federal Register Citation: 64 FR 22981Description
This action clarifies the criteria for unique fittings used in motor vehicle air-conditioning systems, and addresses the acceptability of HFC-4310mee and HCFC-225ca/cb. The end-uses for these substitutes are in metal cleaning and solvent in aerosols. C3F8, HFC-236fa, and C4F10 are found acceptable with use conditions for halon 1301 in-fire suppression and explosion prevention. The unacceptability of substitutes in the refrigeration and air conditioning, solvents, aerosols, fire suppression, and adhesives, coatings, & inks sectors are also listed.Rule 2 - Cross-media evaluation of risks to human health and environment by sector
Publication Date: May 22, 1996
Effective Date: June 21, 1996
Federal Register Citation: 61 FR 25585Description
EPA is issuing its preliminary decisions on the acceptability of substitutes not previously reviewed by the Agency. Monochlorotoluenes/benzotrifluorides are acceptable subject to use conditions as substitutes for CFC-113 and MCF in electronics, precision, and metals cleaning. Blend Zeta and HCFC Blend Delta are acceptable as substitutes for CFC-12 in retrofitted and new motor vehicle air conditioners, subject to the use conditions applicable to motor vehicle air conditioning.Publication Date: July 13, 1995
Effective Date: July 13, 1995
Federal Register Citation: 60 FR 31092Description
EPA issued decisions on refrigerants and solvent cleaning sectors found acceptable subject to use conditions. The refrigeration sector deals with end-uses both retrofit and new equipment. HCFC Blend Beta was found as acceptable subject to use conditions for motor vehicle air conditioning. Blend B was found acceptable subject to use conditions for; centrifugal chillers, chillers, industrial process refrigeration, skating rinks, storage warehouses, refrigerated transport, food refrigeration, ice machines, freezers, dehumidifiers, and air conditioners. HCFC-225 ca/cb is decided as a substitute for CFC-113 and MCF acceptable to use conditions in precision and metals cleaning. Various other substitutes were found unacceptable for refrigerants and air conditioning as well as in the solvents cleaning sector.Publication Date: March 18, 1994
Effective Date: April 18, 1994
Federal Register Citation: 59 FR 13044Description
This final rule promulgates the U.S. Environmental Protection Agency's (EPA) program for evaluating and regulating substitutes for ozone-depleting chemicals being phased out under the stratospheric ozone protection provisions of the Clean Air Act (CAA). In section 612 of the CAA, the Agency is authorized to identify and restrict the use of substitutes for class I and II ozone-depleting substances where the Administrator has determined that other alternatives exist that reduce overall risk to human health and the environment. EPA is referring to the program that provides these determinations as the Significant New Alternatives Policy (SNAP) program. The intended effect of this final rule is to expedite movement away fromozone-depleting compounds by identifying substitutes that offer lower overall risks to human health and the environment. -
Sterilants
Rule 20 (PDF 91 pp, 807 KB) - Prohibition on the use of certain high-GWP HFCs as alternatives
Publication Date: July 20, 2015
Effective Date: August 19, 2015
Federal Register Citation: 80 FR 42870Publication Date: March 18, 1994
Effective Date: April 18, 1994
Federal Register Citation: 59 FR 13044Description
This final rule promulgates the U.S. Environmental Protection Agency's (EPA) program for evaluating and regulating substitutes for ozone-depleting chemicals being phased out under the stratospheric ozone protection provisions of the Clean Air Act (CAA). In section 612 of the CAA, the Agency is authorized to identify and restrict the use of substitutes for class I and II ozone-depleting substances where the Administrator has determined that other alternatives exist that reduce overall risk to human health and the environment. EPA is referring to the program that provides these determinations as the Significant New Alternatives Policy (SNAP) program. The intended effect of this final rule is to expedite movement away fromozone-depleting compounds by identifying substitutes that offer lower overall risks to human health and the environment. -
Tobacco Expansion
Publication Date: March 18, 1994
Effective Date: April 18, 1994
Federal Register Citation: 59 FR 13044Description
This final rule promulgates the U.S. Environmental Protection Agency's (EPA) program for evaluating and regulating substitutes for ozone-depleting chemicals being phased out under the stratospheric ozone protection provisions of the Clean Air Act (CAA). In section 612 of the CAA, the Agency is authorized to identify and restrict the use of substitutes for class I and II ozone-depleting substances where the Administrator has determined that other alternatives exist that reduce overall risk to human health and the environment. EPA is referring to the program that provides these determinations as the Significant New Alternatives Policy (SNAP) program. The intended effect of this final rule is to expedite movement away fromozone-depleting compounds by identifying substitutes that offer lower overall risks to human health and the environment. -
Adhesives, Coatings, & Inks
Rule 20 (PDF 91 pp, 807 KB) - Prohibition on the use of certain high-GWP HFCs as alternatives
Publication Date: July 20, 2015
Effective Date: August 19, 2015
Federal Register Citation: 80 FR 42870
SNAP Notices of Acceptability
These notices expand the list of acceptableThis designation means that a substitute may be used, without restriction, to replace the relevant ODS within the end-use specified. For example, HCFC-22 is an acceptable substitute for R-502 in industrial process refrigeration. Note that all SNAP determinations apply to the use of a specific product as a substitute for a specific ODS in a specific end-use. or pending substitutes for ozone depleting substances (ODSs) under the U.S. Environmental Protection Agency's (EPA) Significant New Alternatives Policy (SNAP) program. The substitutes listed below are acceptable without restriction in the specific end-uses unless designated as pending. A pending substitute can be sold after the 90 day review period has expired, but its acceptability may be affected by a subsequent rulemaking. To see substitutes that are restricted or prohibited, see the list of rules above.
-
Refrigeration & Air Conditioning
Notice 30 (PDF) (14 pp., 354 K)
Publication Date: July 16, 2015
Federal Register Citation: 80 FR 42053EPA is adding options for refrigeration and air conditioning; foam blowing; solvent cleaning; aerosols; and adhesives, coatings, and inks that offer better climate protection without harming the ozone layer. The Determination of Acceptability expands the SNAP program’s list of acceptable substitutes by adding a number of substitutes with lower GWPs compared to what are predominately used today for the same uses.
Notice 29 (PDF) (8 pp., 283 K)
Publication Date: October 21, 2014
Effective Date: 41933
Federal Register Citation: 79 FR 62863Description:
EPA is increasing the options for refrigerants, foam blowing agents, and fire suppressants that offer better climate protection without harming the ozone layer. On October 15, 2014, a Notice of Acceptability was signed expanding the Significant New Alternatives Policy (SNAP) program’s list of acceptable substitutes by adding a number of substitutes with lower global warming potentials (GWPs) compared to what are predominately used today for the same uses. This action also builds on the announcements made on September 16th concerning new private sector commitments to reduce emissions of hydrofluorocarbons (HFCs).Notice 28 (PDF) (8 pp., 283 K)
Publication Date: May 17, 2013
Effective Date: 41411
Federal Register Citation: 78 FR 29034Description:
This notice expands the list of acceptable substitutes for end uses in the refrigeration and air conditioning, foam blowing, solvent cleaning, aerosol and fire suppression sectors. The determinations concern new substitutes.Notice 27 (PDF) (12 pp., 320 K)
Publication Date: August 10, 2012
Effective Date: 41131
Federal Register Citation: 77 FR 47768Description:
This notice expands the list of acceptable substitutes for end uses in the refrigeration and air conditioning; foam blowing; solvent cleaning; adhesives, coatings and inks; and fire suppression sectors. The determinations concern new substitutes.Notice 26 (PDF) (11pp., 203 K)
Publication Date: Oct. 4, 2011
Effective Date: 40820
Federal Register Citation: 76 FR 61269Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, solvent cleaning and fire suppression. The determinations concern new substitutes.Notice 25 (PDF) (24pp., 232 K)
Publication Date: June 16, 2010
Effective Date: 40345
Federal Register Citation: 75 FR 34017Description:
This notice lists acceptable substitutes for HCFC-22, HCFC-142b, and blends thereof for end uses in refrigeration and air conditioning, foam blowing, aerosols, and sterilants. The determinations all include substitutes previously listed as substitutes for other ODS or as substitutes for HCFC-22 alone.Notice 24 (PDF) (9pp., 167 K)
Publication Date: September 30, 2009
Effective Date: 40086
Federal Register Citation: 74 FR 50129Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning and foam blowing. The determinations concern new substitutes. In addition, this document informs the public that the refrigerant blend previously found acceptable under the name KDD5 has received the ASHRAE designation R-438A and has the trade name ISCEON® MO99.Notice 23 (PDF) (9pp., 215 K)
Publication Date: January 2, 2009
Effective Date: 39815
Federal Register Citation: 74 FR 21Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, fire suppression, and foam blowing. The determinations concern new substitutes.Notice 22 (PDF) (5pp., 194 K)
Publication Date: October 4, 2007
Effective Date: 39359
Federal Register Citation: 72 FR 56628Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning. The determinations concern new substitutes.Notice 21 (PDF) (10pp., 214 K)
Publication Date: September 28, 2006
Effective Date: 38988
Federal Register Citation: 71 FR 56884Description:
his notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, foam blowing, cleaning solvents, aerosols, and sterilants. The determinations concern new substitutes.Notice 20 (PDF) (9pp., 219 K)
Publication Date: March 29, 2006
Effective Date: 38805
Federal Register Citation: 71 FR 15589Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, foam blowing, and fire suppression and explosion protection. The determinations concern new substitutes.Notice 19 (PDF) (8pp., 217 K)
Publication Date: October 1, 2004
Effective Date: 38261
Federal Register Citation: 69 FR 58903Description:
EPA has found acceptable additional substitutes for use in the following sectors: refrigeration and air conditioning, foam blowing, fire suppression and explosion protection, and sterilants. This document also clarifies the status of the use of a hydrochlorofluorocarbon as an aerosol solvent, revises the global warming potential for a substitute previously listed as acceptable for use in fire suppression and explosion protection based on new information, and clarifies a statement from the previous SNAP notice of acceptability of August 21, 2003, regarding a refrigerant.Notice 18 (PDF) (8pp., 192 K)
Publication Date: August 21, 2003
Effective Date: 37854
Federal Register Citation: 68 FR 50533Description:
The EPA has approved acceptable substitutes for use in the following sectors: refrigeration and air conditioning, solvents cleaning, foam blowing, fire suppression and explosion protection, and aerosols.Notice 17 (PDF) (10pp., 198 K)
Publication Date: December 20, 2002
Effective Date: 37610
Federal Register Citation: 67 FR 77927Description:
The EPA has approved acceptable substitutes for use in the following sectors: refrigeration and air conditioning, solvents cleaning, fire suppression and explosion protection, and aerosols.Notice 16 (PDF) (7pp., 187 K)
Publication Date: March 22, 2002
Effective Date: 37337
Federal Register Citation: 76 FR 13272Description:
The ozone depleting substitutes are for use in the following sectors: refrigeration and air conditioning; aerosols; and adhesives, coatings, and inks. In addition, we are notifying the public of new information available on the toxicity of HCFC-225ca and HCFC-225cb, acceptable substitutes used in solvents cleaning.Notice 15 (PDF) (5pp., 176 K)
Publication Date: May 23, 2001
Effective Date: 37034
Federal Register Citation: 66 FR 28179Description:
EPA's decision for acceptable substitute uses in the refrigeration and air conditioning sector.Notice 14 (PDF) (13pp., 288 K)
Publication Date: December 18, 2000
Effective Date: 36878
Federal Register Citation: 65 FR 78977Description:
This notice identifies EPA's decisions of acceptable substitutes for refrigeration, air conditioning, foams, non-aerosol solvent cleaning, and aerosol solvents. This action also requests information on the composition and safety of certain refrigerants for motor vehicle air conditioners. This notice also requests information on whether the SNAP program should include review of and establishment of use conditions for operations that involve manual cleaning with solvents or restriction of non-aerosol solvent substitutes to equipment that meets the cleaning equipment standards in the National Emission Standards for Halogenated Solvent Cleaning. Finally, this action updates readers on the SNAP program's review of n-propyl bromide for use as a substitute for ozone-depleting solvents used in the non-aerosol solvents cleaning, aerosol solvents and propellants, and adhesives, coatings and inks sectors.Notice 13 (PDF) (4pp., 254 K)
Publication Date: June 19, 2000
Effective Date: 36696
Federal Register Citation: 65 FR 37900Description:
There are listing of substitutes for refrigeration and air conditioning as well as foam blowing.Notice 11 (PDF) (5pp., 131 K)
Publication Date: December 6, 1999
Effective Date: 36500
Federal Register Citation: 64 FR 68039Description:
This notice applies to substitutes for refrigeration, air conditioning, foam blowing, solvents cleaning sector, and aerosols.Notice 10 (PDF) (6pp., 174 K)
Publication Date: June 8, 1999
Effective Date: 36319
Federal Register Citation: 64 FR 30410Description:
This notice includes substitutes for; adhesives, coatings, and ink sector, aerosols sector, solvents sector, foams sector, and refrigeration and air conditioning sector. Refrigeration and air conditioning end uses include all R-502 end uses in addition to non-mechanical heat transfer, very low temperature refrigeration, and motor vehicle air conditioners. All end uses are applicable for solvent cleaning, aerosol solvents, adhesives, coatings, and ink sector.Notice 8 (PDF) (6pp., 172 K)
Publication Date: February 24, 1998
Effective Date: 35850
Federal Register Citation: 63 FR 9151Description:
This notice contains substitutes for end uses in solvent cleaning, aerosols, foam blowing, and refrigeration and air conditioning. The end uses for foam blowing are CFCs, HCFCs, and polyurethane integral skin, with acceptable substitutions of formic acid and acetone. The end uses for aerosol solvents are CFC-11, CFC-113, MCF, and HCFC-141b, with an acceptable substitution of C5-C20 petroleum hydrocarbons. The solvent end uses include metal cleaning, electronic cleaning and precision cleaning with CFC-113. There are many refrigeration and air conditioning end-uses.Notice 7 (PDF) (5pp., 128 K)
Publication Date: June 3, 1997
Effective Date: 35584
Federal Register Citation: 62 FR 30275Description:
This notice lists GHG-X5, MT-31, HCFC-22, HCFC-142b, and GHG-X5 as substitutes for foam blowing, refrigeration, and air conditioning. The foam blowing end uses are HCFCs, polyurethane integral skin with an acceptable substitute of sub-saturated light hydrocarbons C3-C6. CFC-12 centrifugal and reciprocating chillers, industrial process refrigeration, cold storage warehouses, refrigerated transport, retail food refrigeration, vending machines, water coolers, commercial ice machines, household refrigerators, household freezers, and residential dehumidifiers (retrofitted and new). Also, CFC-12 motor vehicle air conditioning, automotive and non-automotive (retrofitted and new).Notice 6 (PDF) (4pp., 122 K)
Publication Date: March 10, 1997
Effective Date: 35499
Federal Register Citation: 62 FR 10700Description:
This notice contains substitutes for refrigeration and the foam sector. Substitutes include HFC-236fa and saturated light hydrocarbons C3-C6. The refrigeration sector end-use is CFC-114 industrial process refrigeration, with an acceptable substitute of HFC-236fa. The foam sector acceptable decisions are for the end-uses of HCFCs rigid polyurethane and polyisocyanurate laminated boardstock, HCFCs rigid polyurethane appliance, and saturated light hydrocarbons C3-C6. There are various acceptable substitutes for these end uses in the foam sector.Notice 5 (PDF) (8pp., 32 K)
Publication Date: September 5, 1996
Effective Date: 35313
Federal Register Citation: 61 FR 47012Description:
This notice expands the list of acceptable and pending substitutes and clarifies information on refrigerant blends R-410A, R-410B, and R-407C that EPA previously added to the acceptable substitute list. This notice lists acceptable substitutes in various and uses in refrigeration and air conditioning, foam blowing, fire suppression, explosion protection, solvent cleaning, aerosols, adhesives, coatings, and inks. There are also pending substitutes, n-propyl bromide and HFC-4310, listed in aerosols and solvent cleaning.Notice 4 (PDF) (7pp., 146 K)
Publication Date: February 8, 1996
Effective Date: 35103
Federal Register Citation: 61 FR 4736Description:
This notice lists acceptable substitutes for the end-uses of refrigerants, fire suppression and explosion protection, foam blowing, and solvent cleaning.Notice 3 (PDF) (6pp., 172 K)
Publication Date: July 28, 1995
Effective Date: 34908
Federal Register Citation: 60 FR 38729Description:
This notice lists acceptable substitutes for end-uses in refrigeration and air conditioning sector, as well as fire suppression and explosion protection sector.Notice 2 (PDF) (5pp., 218 K)
Publication Date: January 13, 1995
Effective Date: 34712
Federal Register Citation: 60 FR 3318Description:
This notice states acceptable substitutes for the refrigeration and air conditioning sector, as well as the foam blowing sector.Publication Date: August 26, 1994
Effective Date: 34572
Federal Register Citation: 59 FR 44240Description:
This notice lists acceptable substitutes for the refrigeration and air conditioning sector, foam blowing sector, solvent cleaning sector, fire suppression and explosion protection sector, and the aerosol sector. -
Foam Blowing Agents
Notice 30 (PDF) (14 pp., 354 K)
Publication Date: July 16, 2015
Federal Register Citation: 80 FR 42053EPA is adding options for refrigeration and air conditioning; foam blowing; solvent cleaning; aerosols; and adhesives, coatings, and inks that offer better climate protection without harming the ozone layer. The Determination of Acceptability expands the SNAP program’s list of acceptable substitutes by adding a number of substitutes with lower GWPs compared to what are predominately used today for the same uses.
Notice 29 (PDF) (8 pp., 283 K)
Publication Date: October 21, 2014
Effective Date: 41933
Federal Register Citation: 79 FR 62863Description:
EPA is increasing the options for refrigerants, foam blowing agents, and fire suppressants that offer better climate protection without harming the ozone layer. On October 15, 2014, a Notice of Acceptability was signed expanding the Significant New Alternatives Policy (SNAP) program’s list of acceptable substitutes by adding a number of substitutes with lower global warming potentials (GWPs) compared to what are predominately used today for the same uses. This action also builds on the announcements made on September 16th concerning new private sector commitments to reduce emissions of hydrofluorocarbons (HFCs).Notice 27 (PDF) (12 pp., 320 K)
Publication Date: August 10, 2012
Effective Date: 41131
Federal Register Citation: 77 FR 47768Description:
This notice expands the list of acceptable substitutes for end uses in the refrigeration and air conditioning; foam blowing; solvent cleaning; adhesives, coatings and inks; and fire suppression sectors. The determinations concern new substitutes.Notice 25 (PDF) (24pp., 232 K)
Publication Date: June 16, 2010
Effective Date: 40345
Federal Register Citation: 75 FR 34017Description:
This notice lists acceptable substitutes for HCFC-22, HCFC-142b, and blends thereof for end uses in refrigeration and air conditioning, foam blowing, aerosols, and sterilants. The determinations all include substitutes previously listed as substitutes for other ODS or as substitutes for HCFC-22 alone.Notice 24 (PDF) (9pp., 167 K)
Publication Date: September 30, 2009
Effective Date: 40086
Federal Register Citation: 74 FR 50129Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning and foam blowing. The determinations concern new substitutes. In addition, this document informs the public that the refrigerant blend previously found acceptable under the name KDD5 has received the ASHRAE designation R-438A and has the trade name ISCEON® MO99.Notice 23 (PDF) (9pp., 215 K)
Publication Date: January 2, 2009
Effective Date: 39815
Federal Register Citation: 74 FR 21Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, fire suppression, and foam blowing. The determinations concern new substitutes.Notice 21 (PDF) (10pp., 214 K)
Publication Date: September 28, 2006
Effective Date: 38988
Federal Register Citation: 71 FR 56884Description:
his notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, foam blowing, cleaning solvents, aerosols, and sterilants. The determinations concern new substitutes.Notice 20 (PDF) (9pp., 219 K)
Publication Date: March 29, 2006
Effective Date: 38805
Federal Register Citation: 71 FR 15589Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, foam blowing, and fire suppression and explosion protection. The determinations concern new substitutes.Notice 19 (PDF) (8pp., 217 K)
Publication Date: October 1, 2004
Effective Date: 38261
Federal Register Citation: 69 FR 58903Description:
EPA has found acceptable additional substitutes for use in the following sectors: refrigeration and air conditioning, foam blowing, fire suppression and explosion protection, and sterilants. This document also clarifies the status of the use of a hydrochlorofluorocarbon as an aerosol solvent, revises the global warming potential for a substitute previously listed as acceptable for use in fire suppression and explosion protection based on new information, and clarifies a statement from the previous SNAP notice of acceptability of August 21, 2003, regarding a refrigerant.Notice 18 (PDF) (8pp., 192 K)
Publication Date: August 21, 2003
Effective Date: 37854
Federal Register Citation: 68 FR 50533Description:
The EPA has approved acceptable substitutes for use in the following sectors: refrigeration and air conditioning, solvents cleaning, foam blowing, fire suppression and explosion protection, and aerosols.Notice 14 (PDF) (13pp., 288 K)
Publication Date: December 18, 2000
Effective Date: 36878
Federal Register Citation: 65 FR 78977Description:
This notice identifies EPA's decisions of acceptable substitutes for refrigeration, air conditioning, foams, non-aerosol solvent cleaning, and aerosol solvents. This action also requests information on the composition and safety of certain refrigerants for motor vehicle air conditioners. This notice also requests information on whether the SNAP program should include review of and establishment of use conditions for operations that involve manual cleaning with solvents or restriction of non-aerosol solvent substitutes to equipment that meets the cleaning equipment standards in the National Emission Standards for Halogenated Solvent Cleaning. Finally, this action updates readers on the SNAP program's review of n-propyl bromide for use as a substitute for ozone-depleting solvents used in the non-aerosol solvents cleaning, aerosol solvents and propellants, and adhesives, coatings and inks sectors.Notice 13 (PDF) (4pp., 254 K)
Publication Date: June 19, 2000
Effective Date: 36696
Federal Register Citation: 65 FR 37900Description:
There are listing of substitutes for refrigeration and air conditioning as well as foam blowing.Notice 12 (PDF) (3pp., 251 K)
Publication Date: April 11, 2000
Effective Date: 36627
Federal Register Citation: 65 FR 19327Description:
This notice deals with acceptable substitutes for refrigeration, air conditioning, and foam blowing. The end uses for refrigeration and air-conditioning are uranium isotope separation processing (retrofit), using furan as an acceptable substitute for CFC-114. All foam-blowing end uses are included, for saturated light hydrocarbons C3-C6 for HCFC-141b, except HCFC-141b replacement in spray foam applications.Notice 11 (PDF) (5pp., 131 K)
Publication Date: December 6, 1999
Effective Date: 36500
Federal Register Citation: 64 FR 68039Description:
This notice applies to substitutes for refrigeration, air conditioning, foam blowing, solvents cleaning sector, and aerosols.Notice 10 (PDF) (6pp., 174 K)
Publication Date: June 8, 1999
Effective Date: 36319
Federal Register Citation: 64 FR 30410Description:
This notice includes substitutes for; adhesives, coatings, and ink sector, aerosols sector, solvents sector, foams sector, and refrigeration and air conditioning sector. Refrigeration and air conditioning end uses include all R-502 end uses in addition to non-mechanical heat transfer, very low temperature refrigeration, and motor vehicle air conditioners. All end uses are applicable for solvent cleaning, aerosol solvents, adhesives, coatings, and ink sector.Notice 8 (PDF) (6pp., 172 K)
Publication Date: February 24, 1998
Effective Date: 35850
Federal Register Citation: 63 FR 9151Description:
This notice contains substitutes for end uses in solvent cleaning, aerosols, foam blowing, and refrigeration and air conditioning. The end uses for foam blowing are CFCs, HCFCs, and polyurethane integral skin, with acceptable substitutions of formic acid and acetone. The end uses for aerosol solvents are CFC-11, CFC-113, MCF, and HCFC-141b, with an acceptable substitution of C5-C20 petroleum hydrocarbons. The solvent end uses include metal cleaning, electronic cleaning and precision cleaning with CFC-113. There are many refrigeration and air conditioning end-uses.Notice 5 (PDF) (8pp., 32 K)
Publication Date: September 5, 1996
Effective Date: 35313
Federal Register Citation: 61 FR 47012Description:
This notice expands the list of acceptable and pending substitutes and clarifies information on refrigerant blends R-410A, R-410B, and R-407C that EPA previously added to the acceptable substitute list. This notice lists acceptable substitutes in various and uses in refrigeration and air conditioning, foam blowing, fire suppression, explosion protection, solvent cleaning, aerosols, adhesives, coatings, and inks. There are also pending substitutes, n-propyl bromide and HFC-4310, listed in aerosols and solvent cleaning.Notice 2 (PDF) (5pp., 218 K)
Publication Date: January 13, 1995
Effective Date: 34712
Federal Register Citation: 60 FR 3318Description:
This notice states acceptable substitutes for the refrigeration and air conditioning sector, as well as the foam blowing sector.Publication Date: August 26, 1994
Effective Date: 34572
Federal Register Citation: 59 FR 44240Description:
This notice lists acceptable substitutes for the refrigeration and air conditioning sector, foam blowing sector, solvent cleaning sector, fire suppression and explosion protection sector, and the aerosol sector. -
Cleaning Solvents
Notice 30 (PDF) (14 pp., 354 K)
Publication Date: July 16, 2015
Federal Register Citation: 80 FR 42053EPA is adding options for refrigeration and air conditioning; foam blowing; solvent cleaning; aerosols; and adhesives, coatings, and inks that offer better climate protection without harming the ozone layer. The Determination of Acceptability expands the SNAP program’s list of acceptable substitutes by adding a number of substitutes with lower GWPs compared to what are predominately used today for the same uses.
Notice 28 (PDF) (8 pp., 283 K)
Publication Date: May 17, 2013
Effective Date: 41411
Federal Register Citation: 78 FR 29034Description:
This notice expands the list of acceptable substitutes for end uses in the refrigeration and air conditioning, foam blowing, solvent cleaning, aerosol and fire suppression sectors. The determinations concern new substitutes.Notice 27 (PDF) (12 pp., 320 K)
Publication Date: August 10, 2012
Effective Date: 41131
Federal Register Citation: 77 FR 47768Description:
This notice expands the list of acceptable substitutes for end uses in the refrigeration and air conditioning; foam blowing; solvent cleaning; adhesives, coatings and inks; and fire suppression sectors. The determinations concern new substitutes.Notice 26 (PDF) (11pp., 203 K)
Publication Date: Oct. 4, 2011
Effective Date: 40820
Federal Register Citation: 76 FR 61269Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, solvent cleaning and fire suppression. The determinations concern new substitutes.Notice 21 (PDF) (10pp., 214 K)
Publication Date: September 28, 2006
Effective Date: 38988
Federal Register Citation: 71 FR 56884Description:
his notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, foam blowing, cleaning solvents, aerosols, and sterilants. The determinations concern new substitutes.Notice 18 (PDF) (8pp., 192 K)
Publication Date: August 21, 2003
Effective Date: 37854
Federal Register Citation: 68 FR 50533Description:
The EPA has approved acceptable substitutes for use in the following sectors: refrigeration and air conditioning, solvents cleaning, foam blowing, fire suppression and explosion protection, and aerosols.Notice 17 (PDF) (10pp., 198 K)
Publication Date: December 20, 2002
Effective Date: 37610
Federal Register Citation: 67 FR 77927Description:
The EPA has approved acceptable substitutes for use in the following sectors: refrigeration and air conditioning, solvents cleaning, fire suppression and explosion protection, and aerosols.Notice 14 (PDF) (13pp., 288 K)
Publication Date: December 18, 2000
Effective Date: 36878
Federal Register Citation: 65 FR 78977Description:
This notice identifies EPA's decisions of acceptable substitutes for refrigeration, air conditioning, foams, non-aerosol solvent cleaning, and aerosol solvents. This action also requests information on the composition and safety of certain refrigerants for motor vehicle air conditioners. This notice also requests information on whether the SNAP program should include review of and establishment of use conditions for operations that involve manual cleaning with solvents or restriction of non-aerosol solvent substitutes to equipment that meets the cleaning equipment standards in the National Emission Standards for Halogenated Solvent Cleaning. Finally, this action updates readers on the SNAP program's review of n-propyl bromide for use as a substitute for ozone-depleting solvents used in the non-aerosol solvents cleaning, aerosol solvents and propellants, and adhesives, coatings and inks sectors.Notice 11 (PDF) (5pp., 131 K)
Publication Date: December 6, 1999
Effective Date: 36500
Federal Register Citation: 64 FR 68039Description:
This notice applies to substitutes for refrigeration, air conditioning, foam blowing, solvents cleaning sector, and aerosols.Notice 10 (PDF) (6pp., 174 K)
Publication Date: June 8, 1999
Effective Date: 36319
Federal Register Citation: 64 FR 30410Description:
This notice includes substitutes for; adhesives, coatings, and ink sector, aerosols sector, solvents sector, foams sector, and refrigeration and air conditioning sector. Refrigeration and air conditioning end uses include all R-502 end uses in addition to non-mechanical heat transfer, very low temperature refrigeration, and motor vehicle air conditioners. All end uses are applicable for solvent cleaning, aerosol solvents, adhesives, coatings, and ink sector.Notice 8 (PDF) (6pp., 172 K)
Publication Date: February 24, 1998
Effective Date: 35850
Federal Register Citation: 63 FR 9151Description:
This notice contains substitutes for end uses in solvent cleaning, aerosols, foam blowing, and refrigeration and air conditioning. The end uses for foam blowing are CFCs, HCFCs, and polyurethane integral skin, with acceptable substitutions of formic acid and acetone. The end uses for aerosol solvents are CFC-11, CFC-113, MCF, and HCFC-141b, with an acceptable substitution of C5-C20 petroleum hydrocarbons. The solvent end uses include metal cleaning, electronic cleaning and precision cleaning with CFC-113. There are many refrigeration and air conditioning end-uses.Notice 5 (PDF) (8pp., 32 K)
Publication Date: September 5, 1996
Effective Date: 35313
Federal Register Citation: 61 FR 47012Description:
This notice expands the list of acceptable and pending substitutes and clarifies information on refrigerant blends R-410A, R-410B, and R-407C that EPA previously added to the acceptable substitute list. This notice lists acceptable substitutes in various and uses in refrigeration and air conditioning, foam blowing, fire suppression, explosion protection, solvent cleaning, aerosols, adhesives, coatings, and inks. There are also pending substitutes, n-propyl bromide and HFC-4310, listed in aerosols and solvent cleaning.Publication Date: August 26, 1994
Effective Date: 34572
Federal Register Citation: 59 FR 44240Description:
This notice lists acceptable substitutes for the refrigeration and air conditioning sector, foam blowing sector, solvent cleaning sector, fire suppression and explosion protection sector, and the aerosol sector. -
Aerosols
Notice 30 (PDF) (14 pp., 354 K)
Publication Date: July 16, 2015
Federal Register Citation: 80 FR 42053EPA is adding options for refrigeration and air conditioning; foam blowing; solvent cleaning; aerosols; and adhesives, coatings, and inks that offer better climate protection without harming the ozone layer. The Determination of Acceptability expands the SNAP program’s list of acceptable substitutes by adding a number of substitutes with lower GWPs compared to what are predominately used today for the same uses.
Notice 27 (PDF) (12 pp., 320 K)
Publication Date: August 10, 2012
Effective Date: 41131
Federal Register Citation: 77 FR 47768Description:
This notice expands the list of acceptable substitutes for end uses in the refrigeration and air conditioning; foam blowing; solvent cleaning; adhesives, coatings and inks; and fire suppression sectors. The determinations concern new substitutes.Notice 25 (PDF) (24pp., 232 K)
Publication Date: June 16, 2010
Effective Date: 40345
Federal Register Citation: 75 FR 34017Description:
This notice lists acceptable substitutes for HCFC-22, HCFC-142b, and blends thereof for end uses in refrigeration and air conditioning, foam blowing, aerosols, and sterilants. The determinations all include substitutes previously listed as substitutes for other ODS or as substitutes for HCFC-22 alone.Notice 21 (PDF) (10pp., 214 K)
Publication Date: September 28, 2006
Effective Date: 38988
Federal Register Citation: 71 FR 56884Description:
his notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, foam blowing, cleaning solvents, aerosols, and sterilants. The determinations concern new substitutes.Notice 18 (PDF) (8pp., 192 K)
Publication Date: August 21, 2003
Effective Date: 37854
Federal Register Citation: 68 FR 50533Description:
The EPA has approved acceptable substitutes for use in the following sectors: refrigeration and air conditioning, solvents cleaning, foam blowing, fire suppression and explosion protection, and aerosols.Notice 17 (PDF) (10pp., 198 K)
Publication Date: December 20, 2002
Effective Date: 37610
Federal Register Citation: 67 FR 77927Description:
The EPA has approved acceptable substitutes for use in the following sectors: refrigeration and air conditioning, solvents cleaning, fire suppression and explosion protection, and aerosols.Notice 16 (PDF) (7pp., 187 K)
Publication Date: March 22, 2002
Effective Date: 37337
Federal Register Citation: 76 FR 13272Description:
The ozone depleting substitutes are for use in the following sectors: refrigeration and air conditioning; aerosols; and adhesives, coatings, and inks. In addition, we are notifying the public of new information available on the toxicity of HCFC-225ca and HCFC-225cb, acceptable substitutes used in solvents cleaning.Notice 14 (PDF) (13pp., 288 K)
Publication Date: December 18, 2000
Effective Date: 36878
Federal Register Citation: 65 FR 78977Description:
This notice identifies EPA's decisions of acceptable substitutes for refrigeration, air conditioning, foams, non-aerosol solvent cleaning, and aerosol solvents. This action also requests information on the composition and safety of certain refrigerants for motor vehicle air conditioners. This notice also requests information on whether the SNAP program should include review of and establishment of use conditions for operations that involve manual cleaning with solvents or restriction of non-aerosol solvent substitutes to equipment that meets the cleaning equipment standards in the National Emission Standards for Halogenated Solvent Cleaning. Finally, this action updates readers on the SNAP program's review of n-propyl bromide for use as a substitute for ozone-depleting solvents used in the non-aerosol solvents cleaning, aerosol solvents and propellants, and adhesives, coatings and inks sectors.Notice 11 (PDF) (5pp., 131 K)
Publication Date: December 6, 1999
Effective Date: 36500
Federal Register Citation: 64 FR 68039Description:
This notice applies to substitutes for refrigeration, air conditioning, foam blowing, solvents cleaning sector, and aerosols.Notice 10 (PDF) (6pp., 174 K)
Publication Date: June 8, 1999
Effective Date: 36319
Federal Register Citation: 64 FR 30410Description:
This notice includes substitutes for; adhesives, coatings, and ink sector, aerosols sector, solvents sector, foams sector, and refrigeration and air conditioning sector. Refrigeration and air conditioning end uses include all R-502 end uses in addition to non-mechanical heat transfer, very low temperature refrigeration, and motor vehicle air conditioners. All end uses are applicable for solvent cleaning, aerosol solvents, adhesives, coatings, and ink sector.Notice 9 (PDF) (3pp., 155 K)
Publication Date: May 22, 1998
Effective Date: 35937
Federal Register Citation: 63 FR 28251Description:
This is a summary of acceptable decisions of substitutes for aerosol propellants. CFC-11, CFC-12, CFC-114, HCFC-22, and HCFC-142b are being replaced by HFC-227ea.Notice 8 (PDF) (6pp., 172 K)
Publication Date: February 24, 1998
Effective Date: 35850
Federal Register Citation: 63 FR 9151Description:
This notice contains substitutes for end uses in solvent cleaning, aerosols, foam blowing, and refrigeration and air conditioning. The end uses for foam blowing are CFCs, HCFCs, and polyurethane integral skin, with acceptable substitutions of formic acid and acetone. The end uses for aerosol solvents are CFC-11, CFC-113, MCF, and HCFC-141b, with an acceptable substitution of C5-C20 petroleum hydrocarbons. The solvent end uses include metal cleaning, electronic cleaning and precision cleaning with CFC-113. There are many refrigeration and air conditioning end-uses.Notice 5 (PDF) (8pp., 32 K)
Publication Date: September 5, 1996
Effective Date: 35313
Federal Register Citation: 61 FR 47012Description:
This notice expands the list of acceptable and pending substitutes and clarifies information on refrigerant blends R-410A, R-410B, and R-407C that EPA previously added to the acceptable substitute list. This notice lists acceptable substitutes in various and uses in refrigeration and air conditioning, foam blowing, fire suppression, explosion protection, solvent cleaning, aerosols, adhesives, coatings, and inks. There are also pending substitutes, n-propyl bromide and HFC-4310, listed in aerosols and solvent cleaning.Publication Date: August 26, 1994
Effective Date: 34572
Federal Register Citation: 59 FR 44240Description:
This notice lists acceptable substitutes for the refrigeration and air conditioning sector, foam blowing sector, solvent cleaning sector, fire suppression and explosion protection sector, and the aerosol sector. -
Fire Suppression and Explosion Protection
Notice 29 (PDF) (8 pp., 283 K)
Publication Date: October 21, 2014
Effective Date: 41933
Federal Register Citation: 79 FR 62863Description:
EPA is increasing the options for refrigerants, foam blowing agents, and fire suppressants that offer better climate protection without harming the ozone layer. On October 15, 2014, a Notice of Acceptability was signed expanding the Significant New Alternatives Policy (SNAP) program’s list of acceptable substitutes by adding a number of substitutes with lower global warming potentials (GWPs) compared to what are predominately used today for the same uses. This action also builds on the announcements made on September 16th concerning new private sector commitments to reduce emissions of hydrofluorocarbons (HFCs).Notice 28 (PDF) (8 pp., 283 K)
Publication Date: May 17, 2013
Effective Date: 41411
Federal Register Citation: 78 FR 29034Description:
This notice expands the list of acceptable substitutes for end uses in the refrigeration and air conditioning, foam blowing, solvent cleaning, aerosol and fire suppression sectors. The determinations concern new substitutes.Notice 27 (PDF) (12 pp., 320 K)
Publication Date: August 10, 2012
Effective Date: 41131
Federal Register Citation: 77 FR 47768Description:
This notice expands the list of acceptable substitutes for end uses in the refrigeration and air conditioning; foam blowing; solvent cleaning; adhesives, coatings and inks; and fire suppression sectors. The determinations concern new substitutes.Notice 26 (PDF) (11pp., 203 K)
Publication Date: Oct. 4, 2011
Effective Date: 40820
Federal Register Citation: 76 FR 61269Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, solvent cleaning and fire suppression. The determinations concern new substitutes.Notice 23 (PDF) (9pp., 215 K)
Publication Date: January 2, 2009
Effective Date: 39815
Federal Register Citation: 74 FR 21Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, fire suppression, and foam blowing. The determinations concern new substitutes.Notice 20 (PDF) (9pp., 219 K)
Publication Date: March 29, 2006
Effective Date: 38805
Federal Register Citation: 71 FR 15589Description:
This notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, foam blowing, and fire suppression and explosion protection. The determinations concern new substitutes.Notice 19 (PDF) (8pp., 217 K)
Publication Date: October 1, 2004
Effective Date: 38261
Federal Register Citation: 69 FR 58903Description:
EPA has found acceptable additional substitutes for use in the following sectors: refrigeration and air conditioning, foam blowing, fire suppression and explosion protection, and sterilants. This document also clarifies the status of the use of a hydrochlorofluorocarbon as an aerosol solvent, revises the global warming potential for a substitute previously listed as acceptable for use in fire suppression and explosion protection based on new information, and clarifies a statement from the previous SNAP notice of acceptability of August 21, 2003, regarding a refrigerant.Notice 18 (PDF) (8pp., 192 K)
Publication Date: August 21, 2003
Effective Date: 37854
Federal Register Citation: 68 FR 50533Description:
The EPA has approved acceptable substitutes for use in the following sectors: refrigeration and air conditioning, solvents cleaning, foam blowing, fire suppression and explosion protection, and aerosols.Notice 17 (PDF) (10pp., 198 K)
Publication Date: December 20, 2002
Effective Date: 37610
Federal Register Citation: 67 FR 77927Description:
The EPA has approved acceptable substitutes for use in the following sectors: refrigeration and air conditioning, solvents cleaning, fire suppression and explosion protection, and aerosols.Notice 5 (PDF) (8pp., 32 K)
Publication Date: September 5, 1996
Effective Date: 35313
Federal Register Citation: 61 FR 47012Description:
This notice expands the list of acceptable and pending substitutes and clarifies information on refrigerant blends R-410A, R-410B, and R-407C that EPA previously added to the acceptable substitute list. This notice lists acceptable substitutes in various and uses in refrigeration and air conditioning, foam blowing, fire suppression, explosion protection, solvent cleaning, aerosols, adhesives, coatings, and inks. There are also pending substitutes, n-propyl bromide and HFC-4310, listed in aerosols and solvent cleaning.Notice 4 (PDF) (7pp., 146 K)
Publication Date: February 8, 1996
Effective Date: 35103
Federal Register Citation: 61 FR 4736Description:
This notice lists acceptable substitutes for the end-uses of refrigerants, fire suppression and explosion protection, foam blowing, and solvent cleaning.Notice 3 (PDF) (6pp., 172 K)
Publication Date: July 28, 1995
Effective Date: 34908
Federal Register Citation: 60 FR 38729Description:
This notice lists acceptable substitutes for end-uses in refrigeration and air conditioning sector, as well as fire suppression and explosion protection sector.Publication Date: August 26, 1994
Effective Date: 34572
Federal Register Citation: 59 FR 44240Description:
This notice lists acceptable substitutes for the refrigeration and air conditioning sector, foam blowing sector, solvent cleaning sector, fire suppression and explosion protection sector, and the aerosol sector. -
Sterilants
Notice 25 (PDF) (24pp., 232 K)
Publication Date: June 16, 2010
Effective Date: 40345
Federal Register Citation: 75 FR 34017Description:
This notice lists acceptable substitutes for HCFC-22, HCFC-142b, and blends thereof for end uses in refrigeration and air conditioning, foam blowing, aerosols, and sterilants. The determinations all include substitutes previously listed as substitutes for other ODS or as substitutes for HCFC-22 alone.Notice 21 (PDF) (10pp., 214 K)
Publication Date: September 28, 2006
Effective Date: 38988
Federal Register Citation: 71 FR 56884Description:
his notice expands the list of acceptable substitutes for end uses in refrigeration and air conditioning, foam blowing, cleaning solvents, aerosols, and sterilants. The determinations concern new substitutes.Notice 19 (PDF) (8pp., 217 K)
Publication Date: October 1, 2004
Effective Date: 38261
Federal Register Citation: 69 FR 58903Description:
EPA has found acceptable additional substitutes for use in the following sectors: refrigeration and air conditioning, foam blowing, fire suppression and explosion protection, and sterilants. This document also clarifies the status of the use of a hydrochlorofluorocarbon as an aerosol solvent, revises the global warming potential for a substitute previously listed as acceptable for use in fire suppression and explosion protection based on new information, and clarifies a statement from the previous SNAP notice of acceptability of August 21, 2003, regarding a refrigerant.Notice 3 (PDF) (6pp., 172 K)
Publication Date: July 28, 1995
Effective Date: 34908
Federal Register Citation: 60 FR 38729Description:
This notice lists acceptable substitutes for end-uses in refrigeration and air conditioning sector, as well as fire suppression and explosion protection sector.Publication Date: August 26, 1994
Effective Date: 34572
Federal Register Citation: 59 FR 44240Description:
This notice lists acceptable substitutes for the refrigeration and air conditioning sector, foam blowing sector, solvent cleaning sector, fire suppression and explosion protection sector, and the aerosol sector. -
Adhesives, Coatings, & Inks
Notice 30 (PDF) (14 pp., 354 K)
Publication Date: July 16, 2015
Federal Register Citation: 80 FR 42053EPA is adding options for refrigeration and air conditioning; foam blowing; solvent cleaning; aerosols; and adhesives, coatings, and inks that offer better climate protection without harming the ozone layer. The Determination of Acceptability expands the SNAP program’s list of acceptable substitutes by adding a number of substitutes with lower GWPs compared to what are predominately used today for the same uses.
Notice 27 (PDF) (12 pp., 320 K)
Publication Date: August 10, 2012
Effective Date: 41131
Federal Register Citation: 77 FR 47768Description:
This notice expands the list of acceptable substitutes for end uses in the refrigeration and air conditioning; foam blowing; solvent cleaning; adhesives, coatings and inks; and fire suppression sectors. The determinations concern new substitutes.Notice 16 (PDF) (7pp., 187 K)
Publication Date: March 22, 2002
Effective Date: 37337
Federal Register Citation: 76 FR 13272Description:
The ozone depleting substitutes are for use in the following sectors: refrigeration and air conditioning; aerosols; and adhesives, coatings, and inks. In addition, we are notifying the public of new information available on the toxicity of HCFC-225ca and HCFC-225cb, acceptable substitutes used in solvents cleaning.Notice 10 (PDF) (6pp., 174 K)
Publication Date: June 8, 1999
Effective Date: 36319
Federal Register Citation: 64 FR 30410Description:
This notice includes substitutes for; adhesives, coatings, and ink sector, aerosols sector, solvents sector, foams sector, and refrigeration and air conditioning sector. Refrigeration and air conditioning end uses include all R-502 end uses in addition to non-mechanical heat transfer, very low temperature refrigeration, and motor vehicle air conditioners. All end uses are applicable for solvent cleaning, aerosol solvents, adhesives, coatings, and ink sector.Notice 5 (PDF) (8pp., 32 K)
Publication Date: September 5, 1996
Effective Date: 35313
Federal Register Citation: 61 FR 47012Description:
This notice expands the list of acceptable and pending substitutes and clarifies information on refrigerant blends R-410A, R-410B, and R-407C that EPA previously added to the acceptable substitute list. This notice lists acceptable substitutes in various and uses in refrigeration and air conditioning, foam blowing, fire suppression, explosion protection, solvent cleaning, aerosols, adhesives, coatings, and inks. There are also pending substitutes, n-propyl bromide and HFC-4310, listed in aerosols and solvent cleaning.