Search Frequent Questions
Filter By:
- Air Emissions Inventories Total results: 34
- Asbestos Total results: 141
- Butte Area/Silver Bow Creek Total results: 17
- Coronavirus (COVID-19) Total results: 33
- East Palestine, Ohio Train Derailment Total results: 148
- Emergency Planning and Community Right-to-Know Total results: 301
- Fuel Program Total results: 693
- Great Lakes Funding Total results: 92
-
Lead
Total results: 398
- Lead Abatement, Risk Assessment and Inspection Total results: 49
- Lead in Drinking Water Total results: 25
- Lead in Products Total results: 1
- Applying for Certification or Accreditation Total results: 22
- EPA/HUD Real Estate Notification & Disclosure Rule Total results: 24
- General Information About Lead Total results: 9
- Lead-Based Paint Program Fees Total results: 9
- Lead at Superfund Sites Total results: 3
- Lead Renovation, Repair and Painting Total results: 237
- Testing for Lead Total results: 19
- MOVES Total results: 57
- Norwood Landfill Site Total results: 30
- Oil Regulations Total results: 96
- Permitting Under the Clean Air Act Total results: 19
- Radiation Total results: 1
- Risk Management Program (RMP) Total results: 285
- Southeast Minnesota Groundwater Total results: 11
Active filters:
Remove all filtersDisplaying 1 - 15 of 75 results
-
Where can I get more information or copies of the lead-based paint abatement application forms and instructions?
Answer: Information regarding certification under EPA’s lead-based paint abatement program is available at https://www.epa.gov/lead/lead-based-paint-abatement-and-evaluation-program-overview . Question Number: 23002-32438 Find a printable PDF copy of all frequent questions pertaining to lead .
- Last published:
-
Is there lead in lipstick?
Answer: In response to a number of inquiries regarding reports of lead contamination in lipstick, the U.S. Food and Drug Administration (FDA) developed and validated a method for analyzing lead content in currently marketed lipstick. Learn more . Question Number : 23002-33252 Find a printable PDF copy of all frequent…
- Last published:
-
When must I take refresher training?
You must take refresher training before you apply for recertification to EPA. You should begin looking for available courses well before your current certification expires, because refresher courses may not be available in your area on a frequent basis. However, EPA recommends that you take your refresher training no earlier…
- Last published:
-
When do persons applying for certification as inspectors, risk assessors, or supervisors apply to EPA, before or after taking the 3rd party exam?
Answer: Persons applying for certification as inspectors, risk assessors, and/or supervisors must apply to EPA before taking the 3rd party certification exam. For more information about applying for certification as a lead-based paint abatement professional please refer to EPA’s Lead-based Paint Professionals page . Question Number: 23002-33448 Find a printable…
- Last published:
-
When individuals apply for certification in the Federal program under 40 C.F.R. 745.226(a)(1)(i), how long will the certification last?
Answer : For individuals who have taken courses which included a course test and a hands-on skills assessment, the full certification period for individuals applying under 745.226(a)(1)(i) will run for three years from the date of issuance of certification by EPA. For individuals who have taken courses which included a…
- Last published:
-
The definition of “soil sample” at 40 CFR §745.63 relies on certain American Society of Testing Materials (ASTM) standards. Did EPA intend to prevent the use of EPA and HUD standards for soil samples?
Answer: No. In establishing work practice standards for lead-based paint activities, EPA did not intend to prevent the use of EPA/HUD standards. As a general matter, the requirements are not prescriptive but instead state that certain activities be conducted using appropriate documented methodologies. For example, §745.227(c)(3) requires that dust samples…
- Last published:
-
How does the Safe Drinking Water Act limit lead in pipes, plumbing fittings, fixtures, faucets, solder and flux?
Answer: Section 1417 of the Safe Drinking Water Act (SDWA) establishes the definition for “lead free” as a weighted average of 0.25% lead calculated across the wetted surfaces of a pipe, pipe fitting, plumbing fitting, and fixture and 0.2% lead for solder and flux. The Act also provides a methodology…
- Last published:
-
Is exposure to lead contaminated drinking water from absorption through skin a health threat?
Answer: Human skin does not absorb lead in water. For more information visit our website: https://www.epa.gov/ground-water-and-drinking-water/basic-information-about-lead-drinking-water . Question (23002-32377) Find a printable PDF copy of all frequent questions pertaining to lead .
- Last published:
-
Are non-transient, non-community water systems (NTNCWSs) required to monitor for lead and copper?
Answer: All community water systems (CWSs) and NTNCWSs must collect lead and copper tap samples. The frequency of the monitoring and number of samples to be collected and analyzed is based primarily on the number of people served and tap water monitoring results. For an outline of monitoring requirements (e.g…
- Last published:
-
Is there anything else I can do beyond flushing my tap or buying bottled water?
Answer: Yes, find “Important Steps You Can Take to Reduce Lead in Drinking Water” if you are concerned about lead in their drinking water. The list is not intended to be exhaustive or to imply that all actions equally reduce lead from drinking water. EPA recommends you also contact your…
- Last published:
-
My neighbors got their water tested and found lead. Is my water safe?
Answer: Lead usually gets into drinking water through contact with plumbing materials such as lead pipes or lead solder, or faucets, valves, and fixtures made of brass (brass contains some lead). Since each home has different plumbing pipes and materials, test results are likely to be different for each home…
- Last published:
-
Can one still sell lead solder under the Lead Ban?
Answer: Section 1417(a)(3) of the Safe Drinking Water Act (SDWA) prohibits the sale of solder and flux that is not lead-free unless the solder or flux bears a prominent label stating that it is illegal to use the solder or flux in the installation or repair of any plumbing providing…
- Last published:
-
Why do water systems add phosphate to drinking water? What are the health effects of drinking water containing phosphates?
Answer: Public water systems (PWSs) commonly add phosphates to drinking water to prevent the release of metals in drinking water. Orthophosphate is most commonly used for lead and copper control. Polyphosphates sequester iron and manganese to prevent discolored water but are not effective to control lead and copper. Blended phosphates…
- Last published:
-
What must I do to be recertified?
Answer: Prior to the expiration of your current certificate, you must take an accredited refresher training course, you must apply to EPA for recertification, and you must pay a recertification fee. Question Number: 23002-32442 Find a printable PDF copy of all frequent questions pertaining to lead .
- Last published:
-
When do I apply for recertification?
Answer: You must be recertified by EPA before your current certification expires. EPA therefore recommends that you submit your application for recertification no later than 90 days before your current certification expires. Question Number: 23002-32445 Find a printable PDF copy of all frequent questions pertaining to lead .
- Last published: