Search Frequent Questions
Filter By:
- Air Emissions Inventories Total results: 34
- Asbestos Total results: 141
- Butte Area/Silver Bow Creek Total results: 17
- Coronavirus (COVID-19) Total results: 33
- East Palestine, Ohio Train Derailment Total results: 148
- Emergency Planning and Community Right-to-Know Total results: 301
-
Fuel Program
Total results: 693
- Diesel Sulfur Program Total results: 7
- E15 comments Total results: 1
- Fuels and Fuel Additives (FFARs) Total results: 2
- Gasoline Sulfur Program Total results: 17
- Other Total results: 6
- Reformulated Gasoline and Anti-Dumping Total results: 431
- Registration Total results: 9
- Registration and Reporting under 40 CFR 79 Total results: 19
- Renewable Fuel Standard (RFS1) Total results: 67
-
Renewable Fuel Standard (RFS2)
Total results: 111
- Renewable fuel definitions Total results: 1
- Application of standards Total results: 4
- Assignment of pathways to renewable fuel Total results: 4
- Foreign producers and importers Total results: 2
- Generation of RINs Total results: 6
- Grandfathering Total results: 8
- Registration Total results: 25
- Reinstating RINs Total results: 4
- Renewable Biomass Total results: 8
- Renewable volume obligations Total results: 3
- Reporting Total results: 37
- Treatment of biomass-based diesel Total results: 3
- Reporting Total results: 22
- Great Lakes Funding Total results: 49
- Lead Total results: 401
- MOVES Total results: 57
- Norwood Landfill Site Total results: 30
- Oil Regulations Total results: 96
- Permitting Under the Clean Air Act Total results: 13
- Radiation Total results: 1
- Risk Management Program (RMP) Total results: 285
- Southeast Minnesota Groundwater Total results: 11
Active filters:
Remove all filtersDisplaying 1 - 15 of 16 results
-
How do I Obtain the Populations for Each of the MOVES Source Types?
See More Frequent Questions about MOVES and Related Models . To output vehicle populations, when setting up your RunSpec select the "Inventory" calculation type from the Scale panel and the "Population" activity option from the General Output panel of the MOVES GUI. The movesactivityoutput table in your MOVES output database…
- Last published:
-
How are Counties Mapped to Fuel Regions in MOVES? How Can I Substitute Alternate Fuel Formulations?
See More Frequent Questions about MOVES and Related Models . The RegionCounty table in the MOVES default database maps each county to a MOVES fuel region (defined by regionCodeID). If you are conducting a County or Project Scale Run, you do not need to modify this table to use alternate…
- Last published:
-
Why Doesn't my Output Vehicle Miles Traveled (VMT) Match my Input VMT?
See More Frequent Questions about MOVES and Related Models . This problem usually occurs when the run specification does not include all possible vehicle and fuel types. MOVES internally allocates the input VMT to each of the source types and fuel types and only reports the VMT for the fuel…
- Last published:
-
While there is no renewable fuel obligation under the RFS2 program for the production or importation of conventional jet fuel, RINs can be generated for renewable jet fuel. Is that right?
See More Frequent Questions about Fuels Registration, Reporting, and Compliance Help . As described in 80.1407, only gasoline and diesel fuels produced or imported into the U.S. are subject to the renewable fuel standards. Thus, only gasoline and diesel fuel volumes produced or imported by an obligated party factor into…
- Last published:
-
What does MOVES Assume for Future Year Fleet Fuel Efficiency and Emissions?
See More Frequent Questions about MOVES and Related Models . MOVES reflects all fuel economy and emissions standards that were final as of the model release date. For a list of recent regulations accounted for in the most recent MOVES version, see the see the Overview of EPA’s Motor Vehicle…
- Last published:
-
How does MOVES Calculate CO2 and CO2 Equivalent Emissions?
See More Frequent Questions about MOVES and Related Models . MOVES calculates the energy it takes to operate an onroad vehicle based on energy consumption rates as explained in the technical reports Greenhouse Gas and Energy Consumption Rates for Onroad Vehicles MOVES3 (pdf) (November 2020, EPA-420-R-20-015) and Exhaust Emission Rates…
- Last published:
-
How does the Fuel Wizard Determine which Fuel Formulations to Modify?
See More Frequent Questions about MOVES and Related Models . The Fuel Wizard only works on fuel formulations that are in your county database (CDB) and it "edits" them to comply with the alterations you provide. If you wish to create a set of alternate fuels, you will need to…
- Last published:
-
Where Does EPA Obtain Default Vehicle Miles Traveled (VMT)?
See More Frequent Questions about MOVES and Related Models . MOVES gets default national vehicle miles traveled (VMT) values from the Highway Performance Monitoring System (HPMS) of the Federal Highway Administration, which collects VMT information from every state. Although this is a good source of consistent total VMT information, the…
- Last published:
-
How Do I Create my Own I/M Program Input Table Using the "Create Template" Option?
See More Frequent Questions about MOVES and Related Models . If you already have an I/M program in your area, you should always begin by exporting the default I/M program in MOVES, reviewing it, making any changes to the default program, and re-importing it, rather than trying to fill a…
- Last published:
-
Where Can I Find Default HPMSBaseYearVMT Values for a Specific County?
See More Frequent Questions about MOVES and Related Models . MOVES does calculate default values for VMT for each calendar year for each county. Since these values are calculated, they are not found in any table in the default database. If you wish to obtain the default estimates, you will…
- Last published:
-
Why Are There No Emissions for the Early and Late Hours of the Day for Certain Source Types?
See More Frequent Questions about MOVES and Related Models . MOVES has no start emissions for the certain source types in certain hours of the day. While we know that a non-zero number of these source types do start late at night, our activity data on these trucks and buses…
- Last published:
-
Why Does the "hourvmtfraction" Table in the MOVES Default Database Include Fractions for roadTypeID 1 (off-network)?
See More Frequent Questions about MOVES and Related Models . The original concept for MOVES assumed that there would be some vehicle miles traveled (VMT) not accounted for in the other four road types. This remaining VMT would be accounted for in roadTypeID=1. As the model developed, it was decided…
- Last published:
-
Can Programs Other Than Microsoft Excel be Used to Edit Input Database Files?
See More Frequent Questions about MOVES and Related Models . Yes. In addition to MS Excel files, in the County Data Manager/Project Data Manager, MOVES can read in other file types using ASCII text and comma separated variables.
- Last published:
-
What are the Units of Road Grade in the Links Table?
See More Frequent Questions about MOVES and Related Models . The field road grade in the Links table should be entered as a percentage rather than a decimal fraction. In other words, a road grade of 4% should be entered in MOVES as 4, rather than 0.04.
- Last published:
-
What Pollutants are Included in “oxides of nitrogen” in MOVES?
See More Frequent Questions about MOVES and Related Models . The definition of NOx in MOVES (NO + NO2 + HONO) is different than the standard NOx definition of NOx (NO + NO2). This change has been made to correct the exhaust NOx emission in MOVES for potential interference with…
- Last published: