Search Frequent Questions

Filter By:

Active filters:

Remove all filters

Displaying 1 - 15 of 51 results

  • Obtaining an RMP ID Number

    How can a facility subject to the Risk Management Plan (RMP) requirements obtain its RMP ID number? The owner or operator of a regulated RMP facility that has already submitted an RMP, may obtain the facility's identification number (RMP ID Number) by contacting the RMP Reporting Center (703-227-7650). An RMP-covered…

    • Last published:

  • Does EPA have enforcement authority for the risk management program regulations?

    Yes. Under §113 of the CAA, the Agency has the authority to bring administrative and judicial actions against violators. Judicial actions can be civil and criminal in nature. Section 113(a)(3) authorizes the Agency to order violators to comply with the risk management program regulations. Under section 113(b), the Agency may…

    • Last published:

  • Criteria for selecting stationary sources to audit

    What criteria will be used to select stationary sources for periodic compliance audits of risk management plans (RMPs) submitted under 40 CFR Part 68, Subpart G? The implementing agency will, according to the regulations at 40 CFR §68.220(b), select stationary sources for audits based on any of the following criteria…

    • Last published:

  • Is there a citizen suit provision applicable to RMP?

    Is there a citizen suit provision applicable to CAA §112 and the risk management program rule? Yes, section 304 of the CAA includes a citizen suit provision for violations of emission standards or limitations promulgated under the Act.

    • Last published:

  • Accessing RMP Data

    Is Risk Management Plan (RMP) data available to the public and, if so, where can it be found? Risk Management Plans (RMPs) prepared and submitted pursuant to CAA section 112(r) are, by statute, available to the public. Members of the general public may obtain RMP data by visiting a designated…

    • Last published:

  • Can a facility divide a process when assigning program levels?

    My process includes a series of interconnected units, as well as several storage vessels that are co-located. Several sections of the process could qualify for Program 1. Can I divide my process into sections for the purpose of assigning Program levels? No, you cannot subdivide a process for this purpose…

    • Last published:

  • If a stationary source has processes ineligible for Program 1, are all processes ineligible?

    If a stationary source has several processes that are covered under 40 CFR Part 68, and some of those processes have had an accidental release within the past five years (effectively making those processes ineligible for Program 1 status), are the individual processes from which no accidents have occurred also…

    • Last published:

  • If a covered process has an accident, when does it lose eligibility for Program 1 status?

    A process covered under 40 CFR Part 68 is eligible for Program 1 requirements if it meets all of the criteria listed at 40 CFR §68.10(b). Those criteria include a requirement that the process cannot have had an accidental release of a regulated substance that led to offsite death, injury…

    • Last published:

  • Applicability of program levels and prevention program requirements for co-located vessels

    I have a tank with 1,000,000 pounds of toluene diisocyanate (TDI), which is covered under the RMP rule, but not under OSHA PSM. Considered by itself, the TDI would be Program 2 for EPA. The tank, however, is close to equipment that has chlorine above the applicable threshold and is…

    • Last published:

  • Changing from a Program 2 or 3 process to a Program 1 process

    If five years have passed since the last accident involving a covered process, and that process meets the other two requirements identified under 40 CFR §68.10(b) for Program 1 eligibility, could that process become a Program 1 process even if it had previously been identified as a Program 2 or…

    • Last published:

  • How may state and local rules be more stringent?

    In what ways may state and local rules be more stringent? Does this document ( General Risk Management Program Guidance ) provide guidance on state and local differences? States and localities may impose more detailed requirements, such as requiring more documentation or more frequent reporting, specifying hours of training or…

    • Last published:

  • Statutory authority and regulatory source for the risk management program

    What is the statutory authority and the regulatory source for the risk management program regulations that are codified in 40 CFR Part 68? The risk management program regulations were promulgated pursuant to the §112(r) accidental release prevention provisions of the Clean Air Act, as amended in 1990. The regulatory sources…

    • Last published:

  • RMP Information Center

    If I have additional questions regarding the RMP regulations, who can I contact via telephone for further assistance? You may contact the EPCRA, RMP & Oil Information Center, a publicly accessible service that provides up-to-date information on the regulatory requirements of the RMP program, including the applicability, program levels, off-site…

    • Last published:

  • Assigning program level 1 if a public receptors is just beyond distance to endpoint

    Our distance to the endpoint for the worst-case release is 0.3 miles. The nearest public receptor is 0.32 miles away. What tools are available to document that the public receptor is beyond the distance to the endpoint so we can qualify for Program 1? The results of any air dispersion…

    • Last published:

  • Process that meets Program 1 requirements and Program 3 applicability

    Program 3 applies to processes in certain NAICS codes as well as any process subject to the OSHA Process Safety Management (PSM) standard, unless the process is eligible for Program 1. If a process meets the requirements of Program 1, but is also in NAICS code 32211 (one of those…

    • Last published: