ETHOS CLEAN
TECHNICAL PRODUCT BULLETIN #SW-58
USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION
ORIGINAL LISTING DATE: JUNE 28, 2011
"ETHOS CLEAN"
LAST COMMUNICATION WITH MANUFACTURER: 09/27/2012
LAST ATTEMPT: 8/11/2021
I. NAME, BRAND, OR TRADEMARK |
---|
ETHOS CLEAN Type of Product: Surface Washing Agent |
II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT |
---|
MAG7 Venture Group, LLC DBA MAG7 Technologies 1 Lepage Place, Suite 100 Syracuse, NY 13206 Phone: Updated information required Fax: Updated information required E-mail: Updated information required (Mr. Greg Goodell or Mr. Trevor Quig) |
III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS |
---|
MAG7 Venture Group, LLC DBA MAG7 Technologies 1 Lepage Place, Suite 100 Syracuse, NY 13206 Phone: Updated information required Fax: Updated information required E-mail: Updated information required (Mr. Greg Goodell or Mr. Trevor Quig) |
IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION |
---|
1. Flammability: Non-flammable 2. Ventilation: Move subject to fresh air. If breathing is difficult, obtain medical help. 3. Skin and eye contact; protective clothing; treatment in case of contact: Wash affected skin area with water. Consult physician of irritation persists. Skin irritation will not occur with most users. Flush eyes with a large amount of water for at least 15 minutes. Consult physician if irritation persists. Wear safety glasses and neoprene or rubber gloves during application. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: NA. Phase separation will not occur within the storage range. Product should be stored out of direct sunlight unless it is in an Ultraviolet (UV) light resistant container. |
V. SHELF LIFE |
---|
2 years in a sealed (unopened) container (tote, drum, pail) as delivered. 1 year in an opened container). |
VI. RECOMMENDED APPLICATION PROCEDURE | ||
---|---|---|
1. Application Method: Apply ETHOS CLEAN to oil or contaminant with sprayer, pressure washer, mop, sponge, brush, or rags. Application times will depend on the level of contaminant with a minimum of 30 minutes recommended soak time. The required soak time to remove oil will vary with oil density and degree of weathering. ETHOS CLEAN separates the oil from the physical surface to allow the oil to be sprayed off with a water rinse. ETHOS CLEAN should be mixed into soil applications to increase the effectiveness and reduce the application time. 2. Concentration/Application Rate: Pure concentrate can be used for heavy contamination. Dilution ratios for most applications range from 2 to 1 (parts water to parts ETHOS CLEAN) to 10 to 1 (parts water to parts ETHOS CLEAN). Dilution ratios are dependent on the contamination level and application with heavier crude oil spills requiring a lower dilution ratio. Dilutions up to 50 to 1 (parts water to parts ETHOS CLEAN) can be used for lighter contaminations and cleaning. Rinse with water after usage for residue free surface. Surface cleaning typically requires 5 to 1 or 10 to 1 dilution ratio. These dilution ratios will require 1 gallon of ETHOS CLEAN per 250 square feet of surface area. These dilution ratios can be used in many applications including shorelines, rocks, and beaches. 3. Conditions for Use: Salt or fresh water (temperature ranges from 35°F to 120°F). Oil or contaminant can be skimmed from the water or rinsed and captured into collection containers and disposed of per local, state, and federal regulations.
|
VII.TOXICITY AND EFFECTIVENESS | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
a. Toxicity:
b. Effectiveness: NA |
VIII. MICROBIOLOGICAL ANALYSIS |
---|
NA |
IX. PHYSICAL PROPERTIES |
---|
1. Flash Point: 142°F 2. Pour Point: 30°F 3. Viscosity: 32 SUS @60°F 4. Specific Gravity: 1.1664 @60°F 5. pH: 11.6 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: Complete in water |
X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS | ||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|