DO-ALL #18

TECHNICAL PRODUCT BULLETIN #SW-24
USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION
LISTING DATE: JULY 14, 2000
"DO-ALL #18"
LAST COMMUNICATION WITH MANUFACTURER: 8/17/2012
LAST ATTEMPT: 7/19/2021

I. NAME, BRAND, OR TRADEMARK
DO-ALL #18 Type of Product: Surface Washing Agent

II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT
Radcob Solutions, Inc. 4800 North State Road 7 Suite #105 Lauderdale Lakes, FL 33319 Phone: (954) 249-2178 Fax: (954) 640-7080 E-mail: Updated information required Web Site: Updated information required (Mr. Adam Goldberg)

III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS
Radcob Solutions, Inc. 4800 North State Road 7 Suite #105 Lauderdale Lakes, FL 33319 Phone: (954) 249-2178 Fax: (954) 640-7080 E-mail: Updated information required Web Site: Updated information required (Mr. Adam Goldberg)

IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION
1. Flammability: DO-ALL #18 is water based, contains no solvents and is non-flammable. 2. Ventilation: Normal room ventilation. 3. Skin and eye contact; protective clothing; treatment in case of contact: Avoid contact with skin, eyes, and clothing. Wear safety glasses or goggles and protective gloves when handling. In case of eye contact, flush immediately with water for at least 15 minutes. If persistent irritation occurs, call a physician. For skin contact, wash thoroughly with soap and water. 4.a. Maximum storage temperature: 100ºF 4.b. Minimum storage temperature: 35ºF 4.c. Optimum storage temperature range: 40 to 100ºF 4.d. Temperatures of phase separations and chemical changes: DO-ALL #18 has a pour point of 32ºF and phase separation occurs at 105ºF.

IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION

1. Flammability:
DO-ALL #18 is water based, contains no solvents and is non-flammable.
2. Ventilation:
Normal room ventilation.
3. Skin and eye contact; protective clothing; treatment in case of contact:
Avoid contact with skin, eyes, and clothing. Wear safety glasses or goggles and protective gloves when handling. In case of eye contact, flush immediately with water for at least 15 minutes. If persistent irritation occurs, call a physician. For skin contact, wash thoroughly with soap and water.
4.a. Maximum storage temperature: 100ºF
4.b. Minimum storage temperature: 35ºF
4.c. Optimum storage temperature range: 40 to 100ºF
4.d. Temperatures of phase separations and chemical changes: DO-ALL #18 has a pour point of 32ºF and phase separation occurs at 105ºF.

V. SHELF LIFE
DO-ALL #18 has a shelf life of at least two (2) years.

VI. RECOMMENDED APPLICATION PROCEDURE
1. Application Method: May be diluted with fresh or salt water. For general use, apply by spray, mop, etc. Agitate severe spots, rinse thoroughly for residue-free surface. 2. Concentration/Application Rate: To clean oil from beaches, rocks, and piers as a shore-line cleaner, first use a pre-treatment or soaking, using one (1) part DO-ALL #18 diluted with three (3) parts of water. Allow 30 to 45 minutes to soften viscous oil deposits (soak time may vary with temperature, oil density, and degree of weathering). After the soaking period, dilute one (1) part of DO-ALL #18 with 15 parts of water and apply with a high pressure water hose (50 - 100 PSI). Oil released can then be removed by vacuuming, skimmers, or absorbents. For normal cleaning of shop machinery, bilges, decks, waterline scum, rigs, and platforms, dilute one (1) part DO-ALL #18 with up to 20 parts of water. For heavy cleaning and degreasing of tanks, barges, engine rooms and soot, oil stained concrete, and petroleum based drilling muds, dilute one (1) part DO-ALL #18 with up to 15 parts of water. For severe cleaning of holding tanks, grease traps, black magic, crude oil, and Bunker C, dilute one (1) part DO-ALL #18 with up to five (5) parts of water. For steam cleaning, dilute one (1) part of DO-ALL #18 with up to 50 parts of water. For pressure washing, dilute one (1) part DO-ALL #18 with up to 30 parts of water. DO NOT USE UNDILUTED ON COMPOSITION FLOORS, WATER-BASED PAINTED SURFACES, OR ALUMINUM. 3. Conditions for Use: Recommended for cleaning petroleum fractions from beaches, rocks, piers, bilges, decks, waterline scum, rigs, platforms, tanks, barges, engine rooms, machinery, holding tanks, and grease traps.

VI. RECOMMENDED APPLICATION PROCEDURE

1. Application Method:
May be diluted with fresh or salt water. For general use, apply by spray, mop, etc. Agitate severe spots, rinse thoroughly for residue-free surface.
2. Concentration/Application Rate:
To clean oil from beaches, rocks, and piers as a shore-line cleaner, first use a pre-treatment or soaking, using one (1) part DO-ALL #18 diluted with three (3) parts of water. Allow 30 to 45 minutes to soften viscous oil deposits (soak time may vary with temperature, oil density, and degree of weathering). After the soaking period, dilute one (1) part of DO-ALL #18 with 15 parts of water and apply with a high pressure water hose (50 - 100 PSI). Oil released can then be removed by vacuuming, skimmers, or absorbents.
For normal cleaning of shop machinery, bilges, decks, waterline scum, rigs, and platforms, dilute one (1) part DO-ALL #18 with up to 20 parts of water.
For heavy cleaning and degreasing of tanks, barges, engine rooms and soot, oil stained concrete, and petroleum based drilling muds, dilute one (1) part DO-ALL #18 with up to 15 parts of water.
For severe cleaning of holding tanks, grease traps, black magic, crude oil, and Bunker C, dilute one (1) part DO-ALL #18 with up to five (5) parts of water.
For steam cleaning, dilute one (1) part of DO-ALL #18 with up to 50 parts of water.
For pressure washing, dilute one (1) part DO-ALL #18 with up to 30 parts of water.
DO NOT USE UNDILUTED ON COMPOSITION FLOORS, WATER-BASED PAINTED SURFACES, OR ALUMINUM.
3. Conditions for Use:
Recommended for cleaning petroleum fractions from beaches, rocks, piers, bilges, decks, waterline scum, rigs, platforms, tanks, barges, engine rooms, machinery, holding tanks, and grease traps.

VII. TOXICIY AND EFFECTIVENESS

a. Toxicity:

Material Tested	Species	LC50 (ppm)
DO-ALL #18	Menidia beryllina Mysidopsis bahia	66.10 96-hr 288.00 48-hr
No. 2 Fuel Oil	Menidia beryllina Mysidopsis bahia	9.10 96-hr 0.65 48-hr
DO-ALL #18 & No. 2 Fuel Oil (1:10)	Menidia beryllina Mysidopsis bahia	9.38 96-hr 0.57 48-hr
Reference Toxicant (SDS)	Menidia beryllina Mysidopsis bahia	6.36 96-hr 16.53 48-hr

b. Effectiveness:
NA

VIII. MICROBIOLOGICAL ANALYSIS
NA

IX. PHYSICAL PROPERTIES
1. Flash Point: > 200ºF 2. Pour Point: 32ºF 3. Viscosity: 1.8 at 68ºF 4. Specific Gravity: 1.07 at 68ºF 5. pH: 13.1 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: NONE 8. Additives: CONFIDENTIAL 9. Solubility in Water: Soluble with water

X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS

Compound	Concentration (ppm)
Arsenic	ND (< 0.02)
Cadmium	ND (< 0.02)
Chromium	ND (< 0.02)
Copper	0.33
Lead	ND (< 0.02)
Mercury	ND (< 0.00)
Nickel	ND (< 0.10)
Zinc	0.28
Cyanide	0.26
Chlorinated Hydrocarbons	ND (< 0.30)

DO-ALL #18

Emergency Response